Search results

Are there any 2025 Labor Day deals on factory extended warranty? I've decided that my 2023 JTRD is a keeper. Bought in March of 2024, and currently at 30,000+ miles it has been flawless, but I am worried about modern day diesel emissions stuff and modern complicated electronics in general. I...

Hey folks, I just finished installing the Airlift 1000 kit 60830 on our 2023 JTRD. My air fittings are just tie wrapped to the bumper until I figure a clean way to permanently mount the air fill valves. Where and how did you folks mount your air bag fill valves? Maybe I won't have to...

Anyone consider replacing the aux battery with a capacitor? This would be like one of the capacitors used by some folks to stabilize power when running the super sized aftermarket audio equipment?

Anyone installed Diode Dynamics Elite headlights in a diesel Gladiator? I've into a problem running the passenger side cable from the headlight bucket to the turn signal connector in our 2023 JTRD. The videos I can find are all for gas engines. The Ecodiesels have their air intakes, battery...

Looking to flat tow our JTRD and prefer to use a flat tow rated winch bumper. (Preferred over a baseplate or the Maximus 3 tow loops.) The only tow rated bumpers (vs those that are strong enough but not rated) I have found are the LOD and the Rock Hard. So, am I lucky enough to posted this on...

So I am planning to replace my exterior (non headlight) incandescent bulbs with LED bulbs in the OEM incandescent housings. I plan to use a programmer to set the light settings to LED. I would like to know what LED replacement bulbs folks here have used with good results with respect to: 1.)...

Is there a good dealer for service thread? I searched here and on the JL forum as well and couldn't find one. That being said, we are looking for a dealer with a good service department in the Lancaster to Lebanon, PA, area, preferably one good with the eco diesel. We don't have any issues yet...

I have found conflicting information on this subject with my searches and on the Smittybilt web site, so here goes... Can you flat tow with either the Smittybilt XRC or SRC bumpers? I ask because there are locally some new Smittybilt bumpers on the Facebook market near me. And the Rock Hard...

How do you make LED bulbs work in the non LED housings? We have a 23 Ecodiesel Rubicon, bought off the lot, and did not come with the LED lighting package. I really dislike the factory halogen headlights, so I just ordered Diode Dynamics Elite headlight But that still leaves the rest of the non...

We bought our 23 Rubicon Ecodiesel off the lot, so it was missing a few things we wanted including missing the factory tow package. And because we may tow in the future I thought I'd ask a few questions now. (Disclaimer: I didn't find my answers in search.) In the gasser JTs there are...

Hey folks, Executive Summary: The fusetaps supplied with my Wolfbox sourced hardwire kit were 15A, way too big for the wire supplied with the hardwire kit. (Edit: I forgot to mention that the wires in question appear to be either 22awg or 24awg.) These fuses should be 2A or 3A. If you have the...

Does anyone make a low current set of auxiliary switches? I would like to control some low current things (5 amps or less) in the cab. A set of 4 to 6 OEM looking auxiliary switches, kind of like the Voswitch JL300, that fit in the factory auxillary switch location would be great. Or better...

Is there an existing source of 12V "Ignition On" power in the rear of the truck bed I could tap in to to power a rear view camera that would mount on top of a bed cap? Secondary question: If there is such a power source, is there a commercially available connector I can buy so I can insert the...

Hi JT folks, I am starting this thread to share information on the, actually our, Alu-Cab Canopy. (I don't know why Alu-Cab call it a Canopy... It's really just a cap.) Before we bought ours we were only able to get some of our questions answered, but now that we have it any concern we had...

Hi folks, We have an Alu-Cab cap that currently has a CHMSL (Center High Mounted Stop Light) that I have yet to connect.... Because I prefer to avoid cutting into factory wiring harnesses when possible. So, it would be nice to find a Plug 'n Play way to power the Alu-Cab supplied CHMSL...

My bed, maybe everyone else's beds, have two holes each side in the forward upper panel. I just wanted to know if they have some purpose, for example, for an option I don't have. I'll probably plug mine anyway.

I just got a new takeoff Mopar 68334758AA receiver hitch without instructions or bolts. So, to anyone has installed the Mopar receiver hitch, could you... 1. Photograph or scan the instructions, and 2. Make a list of the required nuts and bolts, including the hardware grade and sizes, and...

Any RSI SmartCap owners have Gladiators with soft tops? I'm looking for reviews, comments, and pics. In particular we'd like to know about noise and whether there are any issues with fluttering of the rear window or even contact between the soft top and the cap. And how do you like the soft...

We are looking to fit a hard bed cap on to our JTDR with the Jeep soft top. A local ARE dealer said that he ordered an ARE CX for another customer and it did not fit because the Jeep soft top was longer at the top than the Jeep hard top. He would have needed to slide the cap about 1-1/2 inches...

Looking for a hard shell bed cap for our new to us diesel Rubicon within reasonable driving distance from Lancaster, PA. I figured we'd ask here first before buying new. Here's what it would be going on: Prefer a metal topper to fiberglass, but will consider anything in between nearly new...