Search results

@Discount Tire The new KO3's, have they given any indication on if/when they are going to expand on the sizes available in a 17" tire? I'm going to be looking at 37's in the near future.

I could have sworn there was a line in Settings to have the passenger seat heater come on with remote start (yes I know it's temperature sensitive too) but when I went in in to turn it on only the driver seat and steering wheel were listed. Did an update change this or was it never there and...

I am being very specific here, wanting a specific answer. @Hootbro this is probably right up your alley. Front flare indicator lights. Is there ANY difference between halogen and LED on the harness from the light to the disconnect at the body? The harness comes with the light if ordered...

If you haven't checked it, do it soon. I have low miles on my 2020, just over 12,000. MOPAR recommended interval for cabin air filter is 20,000. I live in central Indiana, not a high dust area. My cabin air filter was almost black and pretty damned full of crap. FYI, the WIX filter is the...

This is the inexpensive one from Amazon that was made for the Colorado/Canyon and fits the JT just fine. I went with the BAK hard roll up cover. Nothing wrong with this one. It wasn't branded as such on Amazon, but it is the Tyger tonneau. It has all the clamps, all the rails, uses velcro to...

Have not been around for a little while. Unfortunately my wife had to go to ER on 18 Jan 2022 because of Covid. She went through the procession, ER, ICU, CCU, ventilator, off ventilator, ICU, regular room, and finally last Friday to a Rehab hospital. She has a long road ahead of her to get...

Anyone else get a Recall notification from CarFax about the following? Y68 2020 JL JT 3.6L Misfire Detection - PCM Software Update When I went to the MOPAR verification site that was tied to it and entered VIN was told there were no recalls?!

15.5 pound bird. Dry brine rub under skin and over skin. One stick of butter cut into pats and laid under skin. Smoked at 180* for 3 hours, turned up to 250* for remainder which was 3 more hours. It came in earlier than I thought. I didn't buy the bird, didn't know the wife was buying one...

For anyone that is or has been interested in a Fumoto Oil Drain Valve, they have them at 15% off with Code : BLACK Sorry, forgot one. Accessories are 30% off with Code: FRIDAY

Synergy has a basic lift kit on their web page. Options are a 1" or 2" lift, with springs, assorted brackets, hardware, and bump stops. They list in the description a Phase 1 and a Phase 2 kit that are not up yet. But at least they moving in that direction...

Maybe this can be made a "Sticky" so people see it. If you're GOING to get your bed spray lined here are some helpful hints. 1.) Do NOT believe the installer when they say they will prep your bed 100%. They won't, they'll spray in all the threaded inserts. 2.) Buy some cheap WOODEN golf tees...

Let me start by saying, got the big red A on the dash this morning. Scrolled to messages and saw "Service Auto Stop Start" I don't use it, turned off with Tazer. But I remembered reading about aux battery being the cause of this so I scroll to "Battery Voltage" and watch the volts. I know...

Just trimmed the hard fat off an 8 pound semi thawed pork butt (pork shoulder, picnic shoulder, however you know it). Going to let it finish thawing then smear with mustard for a binder, rub in copious amounts of sweet dry rub and then tomorrow night it will go in smoker for approximately 16...

I installed a Baja Designs 10" light bar in wide driving (40 degrees) pattern in amber. Wanted some fill further out than OEM LED fogs offer. Have always found amber/yellow does better in foggy or snowy conditions. Here are some pix, light bar only, fogs and light bar, then added headlights, all...

So, Monday I start work at a new job. I am a steamfitter by trade. I go to Kokomo, Indiana to work at the Stellantis engine plant. They are retooling and adding pipe capacity to existing building. So now JEEP will be paying me to make my JEEP payment. So all of you keep making your monthly...

When I installed my front bumper and winch, I used sticky zip tie blocks to anchor the fog light harness. Did a couple of loops to take up slack and put the zip tie blocks in those locations. Well, I didn't pay attention to where things were when I mounted winch and tightened everything down...

The ones I am asking about are on the plastic bumpers. Do they all attach the same way? Across the different trims? Mine is a Rubicon, they don't have the "wings" that stick up in front of the tires. Have 7 or 8 tree pins holding them on. If they all attach in the same pattern, then I have a...

This is off of the plastic bumper of a Rubicon, the steel skid plate that does NOT attach to the bumper. Includes everything needed (4 brackets, 8 bolts to attach brackets, 4 bolts to attach skid to brackets) EXCEPT the nutserts. You will have to source those yourself. I will ship BUT, buyer...

Not going in depth, cut and dry and has been covered elsewhere. Main thing I want to mention, after seeing someone else say they galled some threads on a bolt, the top outside mounting holes on the frame horns might need to be drilled out. Both of mine the ID of the backside was smaller than...

Rear aftermarket bumper is next on my list. The bumper I am going with has mounting points for 3" x 3" surface mount lights. Which would be best for this location, flood or spot? Thanks