Search results

Was sitting at a traffic light this morning. Heard a funny noise and then saw this. Wasn't using defrogger, it was raining. Seems to be happening quite often from what I see on the gladiator Facebook group So much for gorilla glass. Glad I got the warranty. We'll see how long this is to...

Interesting. I bet it would interfere with the trail camera.

Is this why they are called rock rails? Put the ARB compressor in today, with the Epic Afventure outfitters Kracken kit. Went smoothly in under 2 hours.

Just looked, they are listed at $390 now. Kinda upset I didn't buy a set. But I just bought my coopers

I squeezed it through a trail that the wranglers were afraid I wasn't going to make it through with a kayak on top.

So I put 37x12.50r17 Cooper Stt Pros on my gladiator, when I first drove it it would have a slight bounce at 70mph getting worse till 80, edit: Ok 85 but I got scared. After Maybe 300-400 miles the bounce at 70 is gone. I am balancing these with magnum+ balancing beads, 14.5oz per tire, but I...

Don't let this be an under rated comment. Go to another nearby dealer, let them know and see what their techs say.

Wow I never would have thought that they would have automated that fully, I would think they'd use robots but have humans physically checking alignment. Here I am a machinist doubting what machinery can do. Lol. Also I miss understood OP's post I thought he was talking cab to bed alignment...

I actually haven't looked at the bolts, I assumed they were bolts top down, and there would be nuts at the bottom that could be loosened. I don't remember seeing bolts on my un finished bed, although that was a year ago and I was too excited to get my jeep. Also, I would think they had guides...

Ok guys I hate this color. you can hardly tell it's dirty./s Addendum: No one that I've met in saint louis has seen another gecko gladiator. Not even the dealership. I've seen a mojave driving around.

Well, you should be able to unbolt the bed from the frame, or loosen it, and shove it so it's gapped correctly, unless they welded the frame tabs wrong. My front bumper mounts weren't exactly aligned from the factory, they must have had a hell of a time mounting the bumper. Took me 20 minutes...

Damn I love this jeep. Finally broke the 10000 mile mark after over a year of owning it. Had a good time with a local jeep club today

Ok kind of reviving a dead thread here, but has anyone put their transfer case in 4 low, shifted from neutral to drive, but the jeep is in reverse? Like not coasting like still in neutral, but in reverse? Had a scare today after hearing an ominous pop earlier that I can only assume was my...

Hammer.

Yea. I was actually mildly annoyed. I can see fine out of my friends JKU, But then Jeep decided to tilt the windshield for aerodynamics and now I have to duck.

I've also considered this, however being 6'5" I already have to duck to see traffic lights, I worry that this won't help. Also considering an external mounted bar to run limb risers.

Ok so I barely have room between my jeep's roof and my garage door. Is there a light bar that mounts flush or reasonably close to flush to the roof line of the jeep? I'm talking I have an inch and a half to two inches of room. I could always tape a shoe horn to the top of the garage to help it...

Here's the seemingly obligatory build thread. Starting with a photo dump and I'll update this with more info as I get time. 2021 Rubicon Ecodiesel. Gecko green Hutchinson rock monsters (BL-107 rubber inner rings) 37x12.50r17 Cooper Discoverer STT Pros 2.5" mopar lift Warn evo 10 winch Passenger...

There are several different ones. Search for the Eco diesel bottoming out thread. I believe most are posted in there.

How high above the roofline does the pro 6 sit? I have a garage clearance problem that I'm trying to avoid. Turns out Lift kits for Jeeps are much cheaper than lift kits for garages.