OEM Auto Light Switch install?

[NewGladdyOWNR]

I don't think Auto-High Beams is part of this, but I may be wrong. I have the automatic headlights, but I don't think I have Auto-High Beams.

Oh shoot, you’re right I misread the thread. Well at least I ordered the correct bezel for the auto headlamps.

Sponsored

 

[ShadowsPapa]

I don't think Auto-High Beams is part of this, but I may be wrong. I have the automatic headlights, but I don't think I have Auto-High Beams.

Auto high beams require the camara/radar unit the ACC uses.
if you have ACC, you have the "hardware" required for auto high beams.

 

[Splenda]

Auto high beams require the camara/radar unit the ACC uses.
if you have ACC, you have the "hardware" required for auto high beams.

I have the adaptive cruise control. I guess I do have automatic high beams. I just want to say that I am so glad that Jeep puts a separate button on the steering wheel for the adaptive cruise control. I use the standard cruise control much more often that the adaptive cruise control.

 

[ShadowsPapa]

I have the adaptive cruise control. I guess I do have automatic high beams. I just want to say that I am so glad that Jeep puts a separate button on the steering wheel for the adaptive cruise control. I use the standard cruise control much more often that the adaptive cruise control.

I have never used the standard cruise control on a jeep that has ACC including our past Grand Cherokees, both JTs, etc. It feels really weird to get into my wife's JLU (built when there were shortages of those parts) or my Eagle and go back to standard cruise and it's really strange.

 

[Splenda]

I have never used the standard cruise control on a jeep that has ACC including our past Grand Cherokees, both JTs, etc. It feels really weird to get into my wife's JLU (built when there were shortages of those parts) or my Eagle and go back to standard cruise and it's really strange.

I feel the same about the ACC when I drive my wife's Equus, which only has ACC. I hate it when someone changes lanes in front of me on the interstate, and the ACC slams on the brakes. I would rather change lanes or get closer to let them know they just jumped in front of me.

 

[ShadowsPapa]

I feel the same about the ACC when I drive my wife's Equus, which only has ACC. I hate it when someone changes lanes in front of me on the interstate, and the ACC slams on the brakes. I would rather change lanes or get closer to let them know they just jumped in front of me.

People that do that sort of lane cutting are the very type that will brake-check you just to show they are in control.
Never actually had it apply brakes very firmly except when someone cut a stop sign and went flying across in front of me. Then we reacted basically at the same time - me and the ACC.

 

[redgladiator2025]

Sun Sensor = 68230114AB Light load sensor for HVAC and Auto Headlights Avoid 68230115AB which is HVAC only.

Headlight Switch = 68542459AA is the one with the auto setting, Avoid 68542460AA it is the one without you already have.

enabled JScan -> Adaptation -> Auto Headlamp & Auto High Beam - Settings -> Auto Headlamp Feature Present On/Off, - Target Value = Active.

enable JSCAN -> Modules -> Body Controller -> Configuration -> Headlamp on with wiper customer settings menu -> Set
(not sure if actually needed but go ahead and turn it on so you can on/off it from the Radio rather than have to jump through JSCAN Menus)

 

[redgladiator2025]

Hello, I’ve been following this thread and today I finally installed on my wife’s 2025 sport her new headlight switch with the auto feature and the sensor on top of the dash. My question is on this J scan. Can you give me some more insight on this please? Where do I download it at and how do I connect it to the Jeep? Is it through the OBD port?

 

[redgladiator2025]

Sun Sensor = 68230114AB Light load sensor for HVAC and Auto Headlights Avoid 68230115AB which is HVAC only.

Headlight Switch = 68542459AA is the one with the auto setting, Avoid 68542460AA it is the one without you already have.

enabled JScan -> Adaptation -> Auto Headlamp & Auto High Beam - Settings -> Auto Headlamp Feature Present On/Off, - Target Value = Active.

enable JSCAN -> Modules -> Body Controller -> Configuration -> Headlamp on with wiper customer settings menu -> Set
(not sure if actually needed but go ahead and turn it on so you can on/off it from the Radio rather than have to jump through JSCAN Menus)

Hello, I’ve been following this thread and today I finally installed on my wife’s 2025 sport her new headlight switch with the auto feature and the sensor on top of the dash. My question is on this J scan. Can you give me some more insight on this please? Where do I download it at and how do I connect it to the Jeep? Is it through the OBD port?

 

[JeepNightHawk]

Hello, I’ve been following this thread and today I finally installed on my wife’s 2025 sport her new headlight switch with the auto feature and the sensor on top of the dash. My question is on this J scan. Can you give me some more insight on this please? Where do I download it at and how do I connect it to the Jeep? Is it through the OBD port?

You'll need an obd scanner and the bypass cable. Google play store has Jscan.

 

[redgladiator2025]

You'll need an obd scanner and the bypass cable. Google play store has Jscan.

Appreciate you. Thanks

 

[Hootbro]

When it comes to JScan, the $15 VEEPEAK OBD2 dongle has done everything I have asked of it. I know there is other OBD2 dongles North of $80+ that seem to be popular, but if you do not want to spend that kind of coin, the VEEPEAK will work for JScan and any changes you make with it.

https://www.amazon.com/dp/B011NSX27A

 

[redgladiator2025]

Appreciate you. Thanks

So I have the parts they came in today, but I’m not understanding where I connect with the red cable

 

[JeepNightHawk]

So I have the parts they came in today, but I’m not understanding where I connect with the red cable

Tons of youtube videos on it.

 

[redgladiator2025]

Hello
Im going through it im stuck on the part where it says turn on or off. It just says “working”. Can you tell me if it takes awhile for it to allow me in parameter before I can select activate.

Sponsored