RH 67
Well-Known Member
Looking Good!We'll see if anyone can tell by looking.................
Sponsored
Looking Good!We'll see if anyone can tell by looking.................
Whelp, I used to jump/ hop out. And now, I place my right heel on it and it help step down. If you have any arthritis in your knee you might feel it a little bit it eases the step for sure. And getting in is left foot and a handle, a lot easier the the jump it was. But I didn’t mind jumping up to the seat either.odd question, how are these when you go to get out, wife is concerned it will get in the way of your leg and prefers a full step. I like the way these look the best, second would be rock hard angled down sliders which act as a step. let me know if the above does not makes sense
Does the Redarc brake controller work with a Gladiator that has the tow package?Nothing super exciting, but I borrowed an idea from @KVJ and filled in the letters on my Redarc bezel to match the other white lettering on the dash and make it pop out a bit more. Pretty happy with how it turned out.
Have one in mine. Works well.Does the Redarc brake controller work with a Gladiator that has the tow package?
I’m thinking about this.Got in yesterday and installed today... whew. Synergy’s trackbar and sector shaft brace. I fully recommend 150%.
Thx. Which wiring harness did you use? Any recommendations on removing the cigarette lighter plug?Have one in mine. Works well.
Does the Redarc brake controller work with a Gladiator that has the tow package?
Yes, mine has the tow package and it works fine with it. I used the Ram Harness from Redarc, and switched the blue andT
Thx. Which wiring harness did you use? Any recommendations on removing the cigarette lighter plug?
Thanks for the info. I saw the video by @WXman. He also used the TPH-020 harness. The missing piece to the puzzle was the cigarette lighter replacement. Your finished product looks great. I’m going to install the same set up.Yes, mine has the tow package and it works fine with it. I used the Ram Harness from Redarc, and switched the blue and
black wires. This made everything 100% plug and play with no splicing required. Here's the harness:
https://www.etrailer.com/Accessories-and-Parts/Redarc/331-TPH-020.html
@WXman did a good video that shows everything other than the cig lighter part here:
https://www.jeepgladiatorforum.com/forum/threads/redarc-tow-pro-elite-installation.27012/
As for the Cig lighter part, I got that idea from @KVJ and someone else on here. you'll need this mounting ring:
https://www.etrailer.com/Accessories-and-Parts/Redarc/331-TPSI-003.html
Removing the lighter is the hardest part of it, that thing fought me for a while. Getting the dash pieces off to get it out was pretty easy, they are just snapped in. Once you have the lighter out, you can either make a small notch in the dash piece (I did this) or file the alignment nub off of the mounting ring. After that it snaps in with no problem. I have the outlet out now in my toolbox, so I could probably take some pictures of it to show you if you want.
Yeah, I talked @WXman through it and he shows it in his video. you basically have to pop those 2 wires out of the Redarc harness at the connector that plugs into the Jeep, switch them and push them back in.Can you expand on your comment where you stated you switched the wires? Did you have to remove wires from the plug and reinsert them? Thanks.
so to say driving before, I never wanted to take my hands off my steering wheel, lots of corrections. (Disclaimer, I did a puck lift of 2.5” no arms and my caster is way out causing excessive wandering) that said... afterwards I can take my hands off and it will drive straighter for longer than before, I can now drive with less corrections, my steering is tighter and bump steer has been minimalized. Going over pot holes or railroad tracks the steering wheel doesn’t want to jerk out of your hands... (disclaimer, I still have wandering but I will be correcting that soon with a true lift, drag link and tie rod replacements)I’m thinking about this.
Can you tell me what your driving was like both before and after the install?
Thanks.
You got that retro fire truck look happening there with the yellow and red. Looks good!Badged her. Looks better IMO with something on the hood to make her pop. I'm planning on some 70/80's scrambler style stripes on the sides but I cant seem to get anyone to call me back for a quote.