What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS]

[Karnaj]

Heres what Ive done since the Covid. Bought some sill protectors, hauled some lumber, drove to the snow, packed some dirt for a new chicken coop, admired my Jeep, bought some bags for the Molle webbing behind the seats, went camping, admired my jeep, removed the 80% portion of the rear seats for the dogs, bought a front license plate bracket after getting pulled over, got attacked by a wasp while driving, admired my jeep, bought a center arm rest cover because of the dogs claws/drool, went camping again, fed some Bison, installed 67 designs and Ram Mount stuff for the iPad with GPS and phone while wheeling/camping, got stuck in a muddy pond on my own property (the GPS didnt help), had my wife pull me out with the tractor, washed my Jeep, admired my Jeep, got stuck in a hale storm with the top off while in the store to buy a tarp just in case of a rain storm... sigh, also got a Groundhog. Did I mention admire my Jeep?

Probably missed a few things, but, well, there ya go!

Would love to know where you picked up that center console cover.

Sponsored

 

[JTJITSU]

Would love to know where you picked up that center console cover.

Amazon: Suparee was the brand. It was like, $20.

SUPAREE for JL Center Console... https://www.amazon.com/dp/B082KSNFYH?ref=ppx_pop_mob_ap_share

 

[Jason Oliver]

Gus barely fits in the lift bay of the garage!
Sitting level now.

Would you care to share the specs and brands of wheels / tires? Looks great!

 

[Bacon]

Installed my Baja Designs LP6 driving combo lights on the bumper. They are hurt your brain bright. I wired them into #1 of the accessory switches. I didn’t bother with the high/low function. I also bought the quadratec daytime running light harness for the backlights, but they don’t come on with the headlight halo using either of the wires, just the headlights. I’ll figure that out some other time, maybe by tapping the factory halo wire.

 

[Deleted member 30519]

Heres what Ive done since the Covid. Bought some sill protectors, hauled some lumber, drove to the snow, packed some dirt for a new chicken coop, admired my Jeep, bought some bags for the Molle webbing behind the seats, went camping, admired my jeep, removed the 80% portion of the rear seats for the dogs, bought a front license plate bracket after getting pulled over, got attacked by a wasp while driving, admired my jeep, bought a center arm rest cover because of the dogs claws/drool, went camping again, fed some Bison, installed 67 designs and Ram Mount stuff for the iPad with GPS and phone while wheeling/camping, got stuck in a muddy pond on my own property (the GPS didnt help), had my wife pull me out with the tractor, washed my Jeep, admired my Jeep, got stuck in a hale storm with the top off while in the store to buy a tarp just in case of a rain storm... sigh, also got a Groundhog. Did I mention admire my Jeep?

Probably missed a few things, but, well, there ya go!

Nice sill protectors .. what kind?

 

[JWest]

Not today, last weekend, added Max-Modular bed rack. Also added Rotopax fuel and water packs along with Maxtrax recovery boards. The awning will arrive next week and the RTT should arrive by the end of the month. Can’t wait to go camping.

 

[JWest]

Today I added an ARB compressor. I mounted it behind the back seat (drivers side) with an 813 Fabricator bracket. Added a 2 way air hose splitter so I can run an air line to each side for easy air ups. Connected power through the auxiliary 4 switch. Works great!

 

[Bacon]

@JWest , Are you able to roll up the tonneau cover with the rack in place?

 

[RemodelMonster]

Installed my BAK X4 Revolver cover. Has been said before, but will +1 that instructions aren't the best and the top bulkhead rubber sleeve fasteners are crap. Otherwise, the cover is great, fits well, looks good, feels quality(time will tell).

Hey Greenman and ESTOJTR,

In case no one's asked yet, could you please post some pics of the Bakflip X4 in the open position along with some shots of how they attach (with Trail rail and without). Also, let us know if you decide to add a mid height bed rack and any adjustments that you may need to do.

I thought the racks from Fishbone and Rebel Offroad might fit and there is a diy rack from What Exit. Also, I think that the the slotted track on the X4 is supposed to work with the Yakima Outpost HD with some extra hardware.

Thanks!

 

[JTPatriot]

Well not today but a few weeks back I installed a Quadratec flashlight mount and flashlight. Then today I installed some Rugged Ridge entry guards front and rear and also removed the Daystar 3/4" front spacers, did not level the stance and replaced them with the Teraflex 1.5" leveling kit. Now it sits level.

 

[Len]

I'm s

Today I added an ARB compressor. I mounted it behind the back seat (drivers side) with an 813 Fabricator bracket. Added a 2 way air hose splitter so I can run an air line to each side for easy air ups. Connected power through the auxiliary 4 switch. Works great!

I'm still debating where I want to mount mine. I've seen along the fire wall next to the front tire, under the hood and various spots inside the cab. I'm leaning toward under the hood. I do like how you have yours behind the rear seat, it put the compressor in the middle of the rig which is ideal. Nice work with the install.

 

[jebsurf]

1.5 taraflex leveling kit.

 

[JWest]

I'm s
I'm still debating where I want to mount mine. I've seen along the fire wall next to the front tire, under the hood and various spots inside the cab. I'm leaning toward under the hood. I do like how you have yours behind the rear seat, it put the compressor in the middle of the rig which is ideal. Nice work with the install.

I debated the same question. Couldn’t be happier with my choice.

 

[Rubi_Rhod]

Past couple days I have Gotten some Rugged Ridge door sill protectors, a voswitch dash phone mount, a waterport pressurized water tank, and a viair air compressor.

Oh, and got a piece of felt for the dash so I can put up my morale patches.

 

[JWest]

@JWest , Are you able to roll up the tonneau cover with the rack in place?

I am. But it’s realistic a 2 person job. But it can be done.

Sponsored