What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS]

[Logan94605]

Also would like to know how you mounted these. Are those the Rubicon rock rails?

Oh I see... It might be this.

https://mountainoffroad.com/products/hide-a-step-black-jl

Sponsored

 

[s35keith]

Installed Thule crossbars from my previous Yukon. I like the look and functionality combined with the Bakflip.

How are they attached?

 

[Mojavicon]

It’s been a very productive day!!

Started off with some new decals:

Then added a little flair. Nothing like a claymore to keep the tailgaters away.

Installed the Swing Case storage compartment.

Then a Ronin Shorty

Then took the OEM junk off and installed the Magnaflow Rock Crawler Cat-back exhaust.

Then installed S&B Cold Air Intake

And then finished it all out with Oracle Bi LED headlights.

Got a lot accomplished today. This weekend is going to be busy too!

 

[dreston]

Done applying Fluid Film on the frame.

 

[PEI-Gladys]

Wait! That's exactly what I want.... Those or the original rock rails right? How'd you do it?

I have those same steps. M.O.R.E Hide-A-Step.
https://mountainoffroad.com/products/hide-a-step-black-jl

This is also the best install video I found. Great tips. The install is the same for the JL as the JT.


Cheer!

 

[jebiruph]

Added PRP beige vinyl and toast tweed seat covers to my gator gladiator.

 

[eternus]

Rugged Ridge. I wanted ones that protected the entire sill, not just the flat parts. So far so good! I think I had to buy them directly as I am unable to find them in my Amazon purchase history.

I actually found mine on Amazon a couple of weeks ago for $50.

Rugged Ridge Sill Guards

 

[BLK HOLE]

Ceramic tint all around.

70% windshield
30% front doors
20% over factory tint back

 

[immaechu]

Picked up 5 x 37s today! Yes they do fit! with no strap

 

[TrainMan]

Rough Country drop steps. They look great, but a few issues. The instructions were really bad. Hardware was all in one bag, the passenger side doesn't fit as flush as the drivers side. Two bolts didn't align and had to be drilled out. It's like the first shift guy left, and second shift took over. I also installed my entry guards. My sister bought the entry guards for my birthday!

 

[Jeepmonster]

Finished wiring up my winch with a Warn power interrupt switch (Warn 62132). I contemplated using a manual switch like I did in my JK, but I thought I would take advantage of the aux switches I had installed earlier. Finding a good clean mounting location was a challenge, so I made a custom bracket out of a piece of ABS I bought on Amazon (12"x12", 1/8" thick). I circled the bolt holes I planned on using.

I used a piece of cardboard to make a template. Then I traced it onto the ABS (with painter's tape, to make the lines visible).

Then I cut it out with a small circular saw and fine tooth hand saw. I used a sanding disc to remove sharp edges and rounded out the corners.

I clamped the flat piece between two pieces of scrap wood and heated it slowly with a heat gun. Then I used another board to slowly form a 90 degree bend.

I drilled a couple holes and threaded in shallow head truss screws (#10). I glued some thick rubber washers to prevent the head from rubbing (and causing a short to ground) later.

I drilled a couple mounting holes (for top of fender) and further shaped it using a sanding disc. I mounted the switch onto the bracket. I oriented it to have the cleanest routing of the positive battery leads (from winch and to battery).

Here it is mounted and tested. I powered the switch/solenoid to Aux 3. I bought a 6mm fender bolt and used touch up paint to match the billet silver of the other bolts. Pretty happy with the outcome.

 

[SF_E60]

67 Design phone holder
RAM Mount w/Grab bar ball mount
Rebel Offroad bedrail system
Line-X bedliner

Waiting to install buildrightindustries drivers side bedside rack system in order to install my power tank.

 

[121Ranger]

Added Baja Designs LP 6 lights and SAE fog lights. Theses puppies are BRIGHT!

 

[AlienGladiator]

Added Bolt hood lock, blacked out grille, fog light bezels, and emblems, added slightly bigger A/T tires to replace the stock all season Bridgestones on the stock wheels, dash mounted phone mount from Amazon, Roav dash cam, Bushwacker bug deflector, and off-brand door sill guards.

I don't have pictures of everything, but these are the bigger things in the photos. I'd like to reiterate I'm very much new to the Jeep life. Incoming is a Sunrider and the bedliner. Sorry if pictures are bad quality, I had to severly resize/crop them to be able to upload.

 

[PNWGladiator]

I used the JScan app to reprogram my speedometer after having my larger tires installed.

Sponsored