What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS]

[Reebtnawi]

Here are pictures of the @ASFIR 4x4 Engine/Transmission skid plate and Transfer Case skid plate installed after coating. I still have to install my coated Fuel Tank Skid Plates. I am waiting on an answer to my question to Asfir 4x4 before installing. It appears these just go on below the existing skid plates using most of the factory bolts. I could not find any pics to ensure I was installing correctly so I paused to get better info. I am happy with the current install and how the coating came out.

Those look awesome! I hope it's pronounced "as fur" rather than "ass fur".

Sponsored

 

[TRI-JAB]

Those look awesome! I hope it's pronounced "as fur" rather than "ass fur".

The @ASFIR 4x4 is so far so good! Keeps the underneath of my JT cozy….

 

[Phishs]

Yes they are the 35x12.5. No issues running them on the stock wheels. I run the psi a little lower to flatten out the tread. You can do the chalk test to make sure the all the tread is touching the ground. So far the tires are wearing evenly.

Nice! What psi did you end up with?

 

[DublF]

Removed Teraflex 1.5 leveling kit and installed RC 2.5 leveling kit. Now that's much better.

 

[Glad Newbie]

The Mopar version comes more completely assembled.

Lee
- the Bestop team
www.bestop.com

I don't know how it would affect your packaging and shipping costs, but it sure makes for an easy install.

 

[DublF]

5" to 7" screen upgrade

Awesome, I'm doing this tomorrow, and upgrading the climate controls too.

 

[AmosMoses01]

This Sunday the FedEx guy surprised me by dropping off the UnderCover Ultra Flex tonneau cover, along with the Go Rhino Dominator D1's I'd ordered. Installed all by myself, so took Sunday afternoon to do the tonneau, then most of yesterday to get the D1's installed. Also got the front RokBloks installed. We got some heavy rains overnight, and the UnderCover performed flawlessly.

Gotta say, the D1's were a bit of a let down. Installed D6's on my wife's JLU a week ago, and they were definitely higher quality. The D1's didn't have the ends capped ...

... so I filled in with spray foam insulation.

The instructions were also bad, so bad that the parts list, well, it isn't totally accurate.

I got them installed, and they do look nice, but if I had a Mulligan I wouldn't get these again.

 

[Foxtail]

Had leather installed today

 

[Sespe]

Those look awesome! I hope it's pronounced "as fur" rather than "ass fur".

I went with "ass-fear"...

 

[Gren71]

Had leather installed today

What did this cost? Looks nice

 

[Escapade]

Mounted my Maxtrax Boards to my Fishbone Half Rack. The problem I had was the half rack would not accommodate the mounting pins for the wide board. Online there were a couple options with brackets that started around 129.00 No thanks. Found a simpson strong steel black T Tie at Home Depot. At first look I knew it would work on my Fishbone half rack. What I did not expect was the holes lining up exactly to fit the recovery boards when I mounted the pins! I did wind up drilling one support hole in each T-Tie only to fit my rack which may or may not have been needed but excited at the end result. Solid Mount. I cut ends off T-Tie to fit this under my IKamper to mount boards lower on the rack to clear tent. No need to cut ends off if you do not have IKamper or tent mounted on top. I will paint match brackets this weekend to match the rack.

Simpson Strong-Tie Outdoor Accents Mission Collection ZMAX, Black Powder-Coated T Strap for 4x4 Lumber-APT4 - The Home Depot

 

[USMC-SSGT]

Not so much what I did TO, but what I did FOR. Small spending spree on my week old Overland. Also a few minor cosmetic badging changes etc. Now I wait……

 

[James H]

Which bumper is this?

Which bumper is this?

Paramount Guardian. Here is the info:

 

[ross613]

Added some Overland flair, i was skeptical about the silver trim, as I’m going for the black and stingray look, but thought it looked pretty badass.

Where did you get your decals? I have an Overland in Sting Gray and really like these.

 

[Bestop]

I don't know how it would affect your packaging and shipping costs, but it sure makes for an easy install.

Packaging, shipping, and don't forget warehousing!

Lee
- the Bestop team
www.bestop.com

Sponsored