Sponsored

Search results

  1. Let's talk bushings! (in track bars anyway)

    Adding my .02... Using a dial indicator, I measured the left and right movement between the axle and frame when turning the wheel left/right on dry concrete drive (22 JT). My Amazon Nexus cheapo track bar allowed for a +/- 0.160 inches for a total play of about 0.320 inches (thus explaining the...

  2. Alu-Cab Canopy Camper Roll Call

    @1983SheepDog - hey SD, I don’t have the laptop with the stl at the moment but if you remind me after the 15th I may be able to find it.

  3. Alu-Cab Canopy Camper Roll Call

    The cap is vented but the hole is in the top. I have it taped closed until I find or make a cap cover to prevent the possibility of water entry. It is under the overhang so it’s pretty dry in there. I have urethane foam pipe insulation between the roof and camper overhang to keep water out while...

  4. Alu-Cab Canopy Camper Roll Call

    Any of the Chinese diesel heaters will work. They come with everything you need. There is a green fuel line that runs up to the fuel pump located up near the top of the "storage locker" and then runs over to the heater.

  5. Warn 8274

    Looks good!

  6. Alu-Cab Canopy Camper Roll Call

    Alu-Cab Diesel Heater Install: Just completed this install and now I have nice hot forced air heat! :-) FYI, these heaters cost less than $150. My JT is diesel so any fuel I carry has two uses. Cheers!

  7. Front Runner Footwell Water Tank

    Has anyone tried this tank in their JT?

  8. New - Under the Front Seat Compressor Mount for JT/JL

    Air tank and hose clam used... (couldn't remove tank photo from prior post as the forum wouldn't let me :-/

  9. New - Under the Front Seat Compressor Mount for JT/JL

    Hi folks, here are my latest thoughs... 1. I was able to get adequate clearance under the seat after replacing the T I had at the compressor outlet with an elbow. This allowed me to pre-install the elbow with the compressor top housing removed and clock the fitting to a much lower height. I...

  10. New - Under the Front Seat Compressor Mount for JT/JL

    I'll try to get some photos and post them. Cutting the carpet was not an issue for me as you can't see any of the carpet with the compressor installed. I'll take a closer look at adding some wire ties to the electrical wires and see how that goes also.

  11. New - Under the Front Seat Compressor Mount for JT/JL

    OK folks, I purchased my mount and have a few comments for those that follow... 1. I have heated seats and the compressor outlet fitting is hitting the wires. This is after using the bracket to trace cut lines on the carpet and removing the carpet under the mount (saves about 1/4"). I have the...

  12. New - Under the Front Seat Compressor Mount for JT/JL

    Anything taller and you need to order the 813 1/2" seat spacers ;)

  13. New - Under the Front Seat Compressor Mount for JT/JL

    What floor openings are available for routing cable and airline? Hopefully there's a floor plug somewhere nearby but this may be wishful thinking! If not, any thoughts about access? Photos of your routing?

  14. Warn 8274

    First test fit of my 8274. The mount is made of welded 1/2" aluminum plate (spaces the bumper out by 1/2" over the stock position. Plenty of clearance between the winch and grill though I did have to rotate one of the controller hose clamps up out of the way.

  15. hello all

    SCAMMER ALERT - henry667 IS A SCAMMER Joined yesterday and sent me this 15 min ago: "Have you checked with Holmes via Holmeskegler123@ aol.com,He has a OEM front and rear steel bumpers he wants to part with" Searched google for the email address and found other scams he's (she's?) tried on...
  16.

    North Carolina WTB OEM front and rear steel bumpers w/ sensor holes

    Bumpity bump bump
  17.

    North Carolina WTB OEM front and rear steel bumpers w/ sensor holes

    Need sensor capable bumper (or I can add the holes myself I guess). Will pay shipping if the price is right.




Top