Search results

West Covina

Here's a picture of how it was installed on my Ram. It basically clamps onto the bottom side of your bed rails, much like a tonneau/cap. I read up on it and it looks like the side mount is too deep for the gladiator's bed, which is interesting because it was originally listed as being...

Pelican BX80 Cargo Case & Universal Side Mount Kit. Used for a few months. Exterior dimensions are 25" length x 17.3" width x 16" height. Universal side mount clamps to bed rails similar to a tonneau cover. Has some light wear on it, no rust. I wish I could ship this but its gigantic. $200...

I have a full set of front and rear fender extensions that were on my Gladiator for a few hundred miles. The rears have some holes drilled to match the rear fenders. $40 local pickup (zip 91791). These cost a lot to ship.

I have 4 Method 703 Titanium in 0 Offset + 1 spare wrapped in BFG KO2 315/70R17 (5 tires) currently on my Jeep. Looking to swap out to a set of OEMs + $1200. Caveat is I don't want to make unnecessary trips to install TPMS or remount/balance right now. Ideally you have a set of OEM (Mojave...

Mopar Auxiliary Switch Bank Kit (82215798AE) This kit is for vehicles with the silver trim rings. Brand new. $260 Located in 91791. I may be able to ship this if I find a box.

DRT Fabrication Universal Hitch Skid Pretty much brand new, was never used. Fits on the Gladiator. $100, located in 91791.

Yeah, I removed everything as shown in the video. The long piece that goes over the width of the front is intimidating but once you get started it comes right off. Just make sure you keep the metal retainers on the trim piece and not the vehicle. I had the majority of the center console apart a...

It's a fairly straight forward and easy project. The most time-consuming parts were replacing the trim that held the 115V Power button to the left of the steering column and removing the cover in the bed (disregard if you don't have bedliner). If you watch this YouTube video in full it will...

If you're talking about the harness for the 115V in the bed - as long as you have the 115V outlet behind the center console you should already have partial wiring to the bed and you can use part number 68398209AB. It replaces part of the rear harness that goes into your tailgate and adds a...

If you've ever taken the center console apart (the part with the AC controls just pops out starting from the right side), you'll get access to the screw that holds the bottom unit in place. You can then detach the media unit off from the rear fairly easily. The faceplate to the media unit also...

What started as taking the dash and misc. trim apart to get rid of some bad rattling ended up with installing the 115V switch/bed outlet and taking the media port cover off. Still have to find some time to install the aux switches.

I just installed the 115V bed outlet on my Mojave this week. On JSCAN I enabled Miscellaneous -> Inverter On/Off Switch Present to Active and that seemed to do the trick. Inverter Module Present On/Off was already Active. Tested w/ a Milwaukee combo charger and it worked fine w/ the car on.

I had the same problem with drifting left, ended up being the toe was off on one side quite a bit from the factory. I had it adjusted and the issue went away.

Hope this helps.

Sorry, to pack them without shipping damage would make them a bit too costly.

2x Mopar Longer (24.25") LCAs 68322798AA I had these LCAs on backorder that were filled before I could cancel and now I have an extra pair. I ended up sanding and spraying all of them with a textured coat to prevent rust because every single one of them were extremely scratched up from shipping...

Now $260

Yeah, the person I talked to at MR highly recommended going with the 0 offset in case I wanted to run a larger/wider tire.

Same as above - Mojave trim w/ MR703 17x8.5, gloss titanium, and 0 offset. Tires are BFG KO2 315/70/17 (C). Originally wanted +25 but don't mind the 0 offset.