Search results

Anyone here install the Nemesis front inner fender liners? The instructions state I’ll need to trim the inner body metal. Looking for advice from anyone who’s done this.

I’m sure this has been covered but I cannot find it. ENGAGE/FREESPOOL knob spins freely even with the set screw fully tightened. The IN/OUT on the remote works but the freespool won’t engage, or disengage? Either way, anyone have an idea as to what’s up?

Anyone running hydraulic bump stops in the rear? I carry a lot of weight when on trips and in addition to adding the frame brace from Shift AutoWerks I was thinking that hydro’s would also help soften and potential shock loads.

I had to remove my Rancho rear shock skids in order to install my RockJock rear anti-sway bar kit. The RJ's use the bolt on the rear of the shock mount to install the lower bracket. Is anyone aware of any shock skids that will accommodate this set-up? Seems most skids I have found use both the...

My ESS stopped working several months ago. Didn’t matter if I was in the parameters for it to work or not. Never had any battery issues, aux or otherwise. Was on a weeklong overlanding trip through northern AZ about 2 weeks ago and it just started working again and it’s still working for the...

It appears that on my drivers' side the coil is all but touching the frame with truck on the ground. On the passenger side in can easily slip a few fingers between the coil and the frame with room to spare. I have a @Clayton Off Road adjustable rear track bar. Do I just need to adjust my track...

I’ve had the Clayton 2.5” Overland Plus with the HD springs for about a year now. I recently added an Expedition One dual swing out rear bumper and relocated the spare. While down there I noticed what I think is too much bow in the rear springs and my bump stops are not centered. I believe they...

I posted in the electronics section but have not gotten any help so I'm trying here and refining my question. I have the Diode Dynamics SS3 pods that will be mounted in my rear bumper. I have the Lasfit Aux switches in the cab. The lights came with a 3-wire switch that I will not be using, main...

I’m looking for a little guidance on wiring up my Diode Dynamics stage lights into my bumper. They have the red backlight as well. I have the Lasfit aux switches that I’m going to wire them into. They come with a 4 wire set up. I’m not going to use their switch. My questions are: 1. Do I cut...

Recently upgraded front end steering components, sector sharply brace, ball joints, tie rod, drag link and steering stabilizer. I got the non adjustable Falcon stabilizer. Everything is good, alignment, torques, etc, except when turning my wheels are not recentering. On big swooping turns the...

As title says, driver side under cowling. Moved my HAM antenna from passenger side to here and found this.

I am an admitted idiot with math. My alignment specs for toe are... Driver: 0.07* Passenger: 0.06* Total toe: .13* Is that in the popular 1/8" toe in range?

I spent the last few days installing Metalcloak Baller Joints, Steer Smarts sector shaft brace, RPM 2.5 ton tie rod/drag link and Falcon steering stabilizer. Overall very happy so far, barely driven it. Took for alignment. How do we like my numbers? Also, steering wheel is still a bit crooked...

Working on installing the Steer Smarts Sectir shaft brace and not off to a great start. I’ve managed to get the nut almost removed now it’s just stuck. I just started trying to tighten it back up and it wasn’t really going and then it started to rain so taking a break. Anyone else run into this...

I occasionally see folks with Rubicons/electronic sway bar disconnects putting aftermarket disconnects such as Autolynx. Can someone explain to me the benefits of this? Are the circuit boards for the FAD going bad or some other reasons? My first Jeep so I'm still learning.

I spent yesterday installing American Adventure Labs front inner liners. Prettt straight forward except for passenger side bottom by door. There’s this beefy bracket attached to frame that gets in the way of allowing the quick release bolt to line up and even if they lined up beef bracket blocks...

I asked this same question when doing my lift and the help I received was extremely beneficial, so I figured I'd ask same question for a new topic. I will be upgrading my steering components shortly, hoping for some Labor Day sales, and wanted to do as much as needed while its torn apart. I plan...

Got my REDARC BCDC 1225 all wired up. I transferred this over from last truck. It seems to not be detecting the starter/vehicle. I’ve got solid lights on SOLAR/SURGE/LIPO, but nothing on tbe vehicle led regardless if running or not. I used a ‘add a fuse’ to the heated seats fuse and they still...

Installing Rock Hard sliders and on first body bolt, front drivers side, it was going fine. Doing the back/forth technique and it snapped. Now what? I’ve never had great luck with those left hand taps. Any help is greatly appreciated

Ok JT Forum sleuths, help me out please. 2023 JTR gasser, 3100 miles. About 500 miles on Clayton Overland Plus 2.5” with Falcon sp 2.2 adjustable shocks. Yokohama g003 in 37’s. Stock steering components. I understand that Jeeps are not as quiet as a BMW but want to know if this sound is a “Jeep...