Search results

These are sold. I will update the post properly when I get home.

Picture in the daylight, with no rain. :)

Thanks for the confirmation. I've also listed them on a couple Facebook groups, so we'll see what happens.

Selling a set of 5 Falken Wildpeak A/T 285/70/17 tires. These are the 33” tires that come stock on a Jeep Gladiator Rubicon, if you opt for all terrain tires. I bought these with 11 miles on them. I’ve put just under 7000 miles on them. They’re in great shape and run smooth. I just replaced them...

Gave into the temptation today with a set of the Milestar Patagonia M/T's in 315/70/17. Didn't get a picture on the ground yet with all of the rain and flooding we had today. I'll get some this weekend. I'll have a lightly used set of Falken Wildpeak A/T's 285/70/17 for sale for anyone in the NC...

My Sport (Sting Gray) came with all black lettering. I did find the Rubicon letters on Ebay. They have the gray text and red outline. I'm planning on doing the same black treatment on mine. For what it's worth, I talked to a guy in the group who had this done just over the border from me in...

Behind the passenger kick panel, right below where the antenna enters the cab, is a grounding point.

The antenna? Or the original cable that runs into the Jeep? I'll be honest I don't 100% remember, but I believe I disconnected the antenna from the connector inside the Jeep (that I remember being a bear for me to get at). Then I think I had to tug to get the grommet (the one inside the...

https://www.rustysoffroad.com/jeep-bumpers/rustys-jeep-bumpers/jt-bumpers Scroll down on that page. They also have a Facebook page and are very responsive to chats there.

So, I'm not sure what parts you plan on using, but I went with the Rugged Ridge antenna kit, to get the combiner, mount and wiring. I read, though, that their piece that went from the antenna to the truck (makes a 90 degree turn from the antenna base) is delicate and can break easily. With that...

Same here. I went the opposite of many and replaced the stock antenna with a CB antenna and signal combiner. This way I didn't have to add a separate antenna to use both the CB and radio. That said, I've been in the habit of removing my antenna for a long time, before any auto car wash. So...

Rugged Ridge Arcus Front Bumper & Smittybilt XRC Gen3 12k Winch with synthetic rope. Tensioned the rope using my big ass, so I need to do a proper pre-load of the rope.

Nice, I've got almost the same setup waiting to be installed. I opted to get the Arcus bumper without the Over-Rider bar and I got the XRC Gen 3 12k Winch. Unfortunately the winch was delivered without the bolts that secure the winch to the bumper and the hardware needed to connect the fairlead...

We rarely have back seat passengers. That said, I suppose anything is possible in a wreck. I'm not a physician or a scientist and I did not stay at a Holiday Inn Express last night, but I did go sit in the back seat. I'm 6' 1" and if I sit in the back seat and lean forward my head does touch the...

Configured the Tazer JL/JT Mini and installed the Atomic Monkey MonkeyGear headrest harnesses and fire extinguishers.

New bumper from Rusty's Off-Road. It's a pricey piece, but absolutely top notch and it addresses the back corner rail protection that the Sports are missing. This bumper will use the stock rear rock rail brackets on a Rubicon. In my case Rusty's also makes HD brackets for those who didn't come...

I know this is an old thread, but I thought I'd share. I ran into this when setting my tire size. I reached out to SuperChips and they were responsive, but in the end, I came up with a workaround that worked pretty solid for me. To start with, setting to 35" is likely going to leave your speedo...

Finished up my on board air and 4x8 sheet goods setup. The tank mounts are Quick Fist tank straps (the 2 1/2 to 9 1/2 diameter size). They're hard to see, but I setup 2x4 blocks (glued and screwed to the plywood) between the tanks and on the ends, to keep them in place. I also drilled those...

Started working on integrating my on-board air mounting into the piece that will allow me to haul 4x8 sheet goods. I've got everything fitting right. Need to paint the wood and get the CO2 tank mounts. I'm going to mount the plywood to the 2x4 with screws, something easy to remove when needed...

https://www.etsy.com/listing/710347975/jeep-gladiator-t-shirt