Search results

Yes, it works identical to the RAM installation. I got my J2354 programmer on amazon. Its the mongoose jeep/chrysler adapter. I'll sell mine for $250 plus shipping if you don't mind a used one...

I"ve added both front and rear park assist to my base model jeep. While the factory installs the park assist module in the passenger rear quarter panel right in front of the tail light, underneath the plastic panel, I chose to add mine behind the gateway security module. SInce I was running...

its located at the passenger rear, inside the jeep, not in the tail light cavity. you'll have to pull that plastic cover off back there to see where it mounts up. If you are wanting to mount your park assist module back there, more than likely, the studs won't be there. You can buy them from...

adding park assist to the rear is easy. Adding them to the front requires a little bit more of work. I had to source my park assist module from the UK to get the correct one, but can it be done? Absolutely. I have operatitonal front and rear park assist on my base model jeep wrangler sport..

I'm in process of doing this with a 2019 wrangler sport. One more thing to have is a bumper with the holes for the sensors, and the clips to hold them into the bumper. The clips are pretty cheap, I got my steel bumper on ebay for 265. I'm have an issue getting the right settings to enable the...

Did you figure this out? I'm having the exact same problem on my 2019 wrangler. I checked the fuse, F96, and it reads good. I don't get power on either side of the fuse, which points to either the pdc is defective, the wiring from the pdc to the BCM is broken somewhere or the bcm is defective.

Short version is: Replace the firmware on your BCM from a 2020 BCM. Then replace the firmware on your IPC (speedo cluster) to the 2020 IPC. warning: Don't forget to backup your existing configuration before you replace anything.

I finally have a full operational auto high beams setup on a 2019 Jeep Wrangler. It works exactly the way it suppose to, gives me a message that It is enabled when the stalk is moved forward and disabled when I move it forward a second time. The headlights dim when another vehicle is...

So to bring others current, I was able to flash the BCM from 2019 jeep wrangler with no auto highbeams with the 2020 firmware. After the flash, I had to restore the configuration, and I used Alpha OBD to do it. Then with Alpha OBD, I set the Configuration as set to "YES". The flash...

I already ordered a 2020 bcm, so I will go ahead and try that first. Your suggestion is about 30 days out so the bcm will be here first lol. Also, I'm slightly concerned that what happens if the flash of the bcm fails, as in bricking it. Then I lost use of my jeep lol. Not that I depend on...

It changed the byte pair from 80 to 00 by putting the location to none. Here are the results:

My jeep didn't come with a 8.4 or a telematics module. I put the 8.4 in and its been working fine. It still has app control of the jeep. Witech 2 scan shows a bunch of radio communication problems but it doesn't interfere with any operations of the radio or jeep that I can tell. Since I...

I'm not confident that mopar ever intended it to work on a 2019 wrangler. Those who have late December 2019 wrangler JL have the auto highbeams. If anyone who has, or knows of anyone that has a 2019 jeep wrangler or even gladiator and has functional auto high beams, it would be very helpful to...

I have, like most on here when they upgraded their uconnect radio to the 8.4 screen, upgraded their center stack to move the volume control and tune controls to off the radio. Then added a sunlight sensor to get auto headlights, and then car temp sensor to get (fake) auto climate control. I...

Ok I changed the beam on and off thresholds are 25 and 20 respectively. I changed the line to read exactly that, and when I query in alphaobd, it says the state for the location as "undefined". I did another config save and verified that I have it correct as you specified. I went for a quick...

My bad. I tried several settings on it in jscan and left it on as undefined. Use these files instead. I also including a bcm dump to show the settings. I have correctly selected ICRM, and alphaOBD is saying it is set for ICRM. However, JSCAN live data, and witech2 show it as reserved.

I have attached the backup file. Canbus logger? I don't think so. Is it needed? If so, any you recommend? I noticed there are also 3 other reserved settings you can select. How does it differeniate between them? Is it based off a number value thats held in a specific memory slot and not the...

Adding the ICRM heater circuit is fairly straight forwarded on a Jeep wrangler. Not sure if the windshield folds down on a gladiator but it makes the process a 15 min job. The harness I used was part number 68398637AD and listed as antenna wiring oddly. I have a base Jeep with 0 options...

don't think you can see it in alphaobd. Do you have jscan? if so, you can just go to the module screen.