Search results

Having experience with replacing the motor on my 2021 (which was recently totaled by a druggie running a red light), I decided that it was in my best interest to be very aggressive with break in oil changes. To be honest I'm surprised to see so much metal in this filter- and that's with using a...

I posted this before without the proper photo and $. I have the springs also I will throw in with the shocks. These are OEM factory takeoffs from a 2026 Mojave X. Asking $2,000 for the set. Forgive me for not wanting to take them off the shelf to take a picture with my name tag. Located in...

I've tried three different pickle forks from O'Reilly's and one of those ball joint no impact removers... I've tried putting tension on it and whacking it at the side of the pitman arm. It does not want to budge. Open to suggestions, or maybe there's a specific size pickle fork for this beast?

I run 37" Kenda Klevers and SDI eclik on a 2" AEV lift. That kit comes with some hockey pucks that effectively extend the bump stops 2". The shocks also have a bushing to act as additional impact cushion. I feel as if the bump extensions are limiting up travel and preventing the shocks from...

Looking to replace the AEV spacer with a spring. I think the stock springs are a bit squishy, especially with the 37s.

OEM Mopar 3.6L Pentastar Intake Manifold + Bosch 67mm Throttle Body + MAP Sensor – Complete Assembly – Clean & Working Location: North Phoenix (Anthem Way & I-17) Price: $220 for the full setup or priced individually below Selling a complete OEM intake setup from a running 3.6L Pentastar...

I have a 2" AEV lift with 37" Kenda Klevers on stock wheels and eclick shocks. I have the geometry correction brackets front and rear. Long ago I destroyed the factory bump stops and stopped replacing them after warranty was up. I'm thinking the springs are too soft for actual aggressive desert...

I know this isn't an interior "mod" per se but I couldn't find a forum specifically for accessories. Trying to decide the best way to isolate our two dogs (1 great Pyrenees and one Shih Tzu) in the back seat. I have the floor extender u-shaped thing that hangs from the headrest posts, but that...

Fishbone Offroad rack ($1,000+) failed with cracks at all four corners after less than 2 years with a nature nest tent (about 180lbs). They offered only 50% off a replacement, ignoring safety risks. I didn't notice these until removing the RTT. I highly suggest any of you using this rack to...

This sound was happening before my new motor was installed and it's still doing it- a strange thump that sounds almost like a preamp turning on after Auto start stop and on initial startup. It comes from the rear of the truck. I replaced almost everything... Something with the cat maybe?

Thanks to all who helped me out with the questions I had as I swapped my bad motor for a new long block from Powertrain Products LLC. I thought maybe this post could help someone else in the future, so here's a few things that I did that helped and things I wish I knew before I started. New...

Assuming this had something to do with the camshaft wearing out because this is the same cylinder, (number five). It's not why I'm replacing the motor, however. Burnt valve + low compression on other cylinders are contributing factors to that. I've spoken to a few people about whether or not I...

I read in one of the JL forums that removal of the motor is much easier with the lower manifold removed because the top two bellhousing bolts are a royal beach to access with it in place. Of course, I read that after pulling my motor. I'm about to install a long block but I'm still swapping...

For those of you who have pulled the 3.6, how did you do it? I don't really want to buy $300 plates to mount to the exhaust ports. Would lifting straps work?

Long story short - A few months ago I posted on the tick of death I dealt with and it seemed to be running fine until the other day. I was accelerating hard when it threw misfire codes P0300, 0305 & 0306... Cleared codes and did some testing in alfaobd (clean phasers, cam relearn etc) and ended...

I joined the tick of death club. Intake rockers and one lifter were shot on the pass side. Buttoned it all back up and it won't start. My buddy said he heard something hitting the valve cover. Are there common errors to look for as we tear it back down again tomorrow? 2021 Mojave

Being spoiled by having a backup camera on an off-road rig, I wanted to be able to actually use it when it was most needed- in the desert. As soon as you hit the trail, this camera gets completely covered in dust. Sure, I could get out and wipe it on my way to work every day but that method...

Last night I decided to see if a direct route to the Hieroglyphics OHV area near my house was open or if it crossed private property. Turns out, it was open (at least most of the way, because I got sidetracked and never made it to the destination). I recorded a little bit of the run which...

I had the day off so got together with another guy in the area and did some backroads driving this morning. Some of it was a bit rockier than anticipated; made it a little bit challenging and more fun than just going to the mall. :D

My super red nekky no drill no wire tap cb /gmrs install. I may end up with some sort of overhead mount, but the first thing I bought was a cb because the club I ride with most uses it. I also wanted gmrs with a little more power than handheld. I decided to mount both to the same quadratec...