Search results

Depending on the radio. I mounted the radio on the molle panels in the center to the JTM, ran the wires across the top of molle and down the passenger A pillar, there is a valley under the weather strip and to the battery. I ran the antenna wire down the driver A pillar to the antenna.

I found with my mid height rack before going to a full rack that one had to be creative. Here are a couple photos. I acually had a sheet of aluminum and attached it to the top of the rack, I mounted my jerry can holder there. They rings as seen in photo were to hold my generator when I did not...

That would make since about the winch plate and winch. When we were dry fitting everything it was fine, install winch and plate had to modify holes.

From what I have seen and think, the OE bumper and SP from a 392 does not fit onto a JT. They are completely different, in my understanding. There is not much on the 392 that can be used on other Jeeps. I did put a Rubicon steel bumper and SP on my JTM. I did have to open the rear mount holes...

Not just today but for the last couple of months. Been getting ready for first trip of the year, Death Valley first week of April. *Removed old rack and installed full rack *Replaced OE JTM bumper with OE JTR bumper *Warn winch plate and HF 12000lb winch *Flip up license plate, new fail lead...

Go to Rock Auto for OE headlights

I just got a Mopar service notification that It is recommended to change my fuel filter, WTH is this about? 21’ JTM 27K miles 3.6. I didn’t think these had an external filter…..

I just replaced my Mojave OE with a OE Rubi steel bumper, Rubi skip plate, Warn winch plate and a Harbor Freight ZXR 12000 winch this past weekend. I did remove the 65’ of 3/8” cable and installed synthetic rope. My front end dropped about 1/4”. Not bad I figure. I still might add a couple...

I don’t know the hardware for the mojave skid plate only to say I used the rubicon hardware that worked very well. License plate flip up is from Cascadia. I got mine off amazon but you can get them from Northridge or direct from Cascadia.

Update: Installed apex ZXR 12000 lb winch this past weekend. Used the warn winch plate. I took off the JTM plastic bumper and installed a OE Wrangler steel bumper and OE black steel front skid plate. Issues: Either the steel bumper was tweaked a bit or the frame was tweaked a smidge from the...

I had a rock hit the passenger side mirror and put a hole in the plastic cover. It did not break the glass. I purchased the new plastic cover from my dealer. Easy Peasy. I thought the price was very fair as well. My mirror is electric and heated and did not have to buy both. It took less than 15...

I am installing our new to me factory steel JTR bumper on my JTM this weekend, we purchased the warn winch plate for the HF 12000 winch as well, I will let you know how it goes….

My advise, take it out a few times to see what works for you and doesn’t. I learned on my JTM that I do not need to do anything under the truck except skid plates. I have traveled a lot on the west coast trails and utah. I haven’t been anywhere that I needed extra lift, different gearing etc… We...

Just looking for good advise. Have a 21 JTM 26k miles. I have no mechanical mods and will not be adding any ie: lifts, regears etc. I have exterior mods that add weight ie; decked system, full rack, awening, winch and OE winch bumper. We pull a overland trailer fully loaded about 2300 lb. The...

Like most these post. I did a 40% seat delete as well. Made my own platform. I plug a Jackery unit into the truck plug to charge while I drive. I then plug the fridge / freezer into the jackery to keed it cold when outside the jeep exploring the hiking trails and to keep it running during the...

Here is my 2 cents worth. This forum does have a lot of negetivity at times but I am OK with that, it gives me knowledge if I incounter an issue with my 21 JTM. Just remember it’s a good place to vent and most JT’s don’t have issues or very little issues. I love my JTM, said many times on...

I just installed a bed rack this past weekend. I really liked the Hooke Rack and would have purchased it but I feel the rack needs to use the whole bed length. This rack does not. Large void behind the cab and does not go to the end of bed.

Going a different direction! Fishbone O/R half high bed rack. Mounts to the bed rails NOT trail rails. Does not come with Jerry can base platform as in photo. Can possibly deliver or meet half way point Wa, OR or maybe even ID. $400.00 OBO

Spent some time in Idaho the last couple years. Amazing trails. Look on onyx they will show you a bunch of trips. Also, you are very close to Washington and Oregon. Same thing , tons of trips and trails. I am jealous that you are in Idaho, my dream is moving to Idaho although further north than...

I am installing my badlands 12K into my OE steel bumper take off from a JTR this week. I choose the warn winch plate, more money but convinced I need to step up and pay the higher cost.