Search results

Following...

Yesterday the UPS woman brought me two MOPAR Lower Control Arms that are part of the MOPAR two inch lift kit - thanks Benny at forum sponsor AllMoparParts.com . I did these on my 2018 JLUR and they improved steering and caster noticeably. I put them on today. On the JLUR I torqued...

I just did this job., for the second time. Previous was on my JLUR. I use this DeWalt DCF899H If I can't get it off with the 36 inch breaker bar. 1200 Ft/Lb of breakaway torque. 20V MAX* XR® High Torque 1/2 in. Impact Wrench w. Hog Ring Anvil (Bare) | DEWALT Sorry to hear about the...

Nice. I like your license plate, too. I have one of those on my vette.

Agree wholeheartedly.

OFF TOPIC: You have got to love all the bicycle racks obstructing license plates on I-95, I-75, I-10, and I-4 in Florida. They get away with it all the time, and I-95 all the way to New York. Obstruct your Jeep license plate with mud, instant ticket. Now back to the muddy tire conundrum.

Or how to get to them on the 3.6L gasser

Yep, every 6 month bill I got the past two years from State Farm have been anywhere from 18% to 28% increases, across all vehicles. No claims, no wrecks, no tickets. They are all doing it and it is unsustainable. Good luck in looking at other options.

Dayum, I always thought your setup was one of the nicer ones I've seen., DIY or aftermarket.

Yep, I went by what is in the owners manual, page 94 in "Getting to know your vehicle" in my 2023 Gladiator Owners Manual. Yeah, I RTFM. Mine is two pine 2X4's, cut to 57 5/8 inches and bottom corners cut on the one that sits on the bed, and also a 50" 2X4 with all corners rounded for the...

About that fender connector, if it is like the wrangler JL there is a little trick to it. Red tab, then squeeze the connector and it pops right out. (1) Aux Battery replacement the easy way... pull the fender flare | Page 2 | Jeep Wrangler Forums (JL / JLU) -- Rubicon, 4xe, 392, Sahara, Sport -...

Shoutout to @dos0711 for stopping by and he was able to get the deed done. They weren't glued afterall. He has my twin gladiator in a 2022, said he didn't recall it being as difficult when he did his. He used a long narrow flat head screwdriver to hold the tab in while yanking on the wires...

Cool, I will send a PM.

Each to their own, I prefer to have options and I'm not complaining. I don't plan on having it bypassed anywhere but in my garage. These connectors are not easy to get to, nor are they easy to unplug. Granted a Z Automotive extension would make it easier for a crook, but if they want your...

I wish.

Thanks for the reply. Wonder if the 2024s also have the glue? Yeah I pulled the panel under the steering wheel and disconnected the door bracket and footwell trim so I can swing the door open wider. My close up vision sucks, but I am going to take a long look to see if I see any signs of glue...

I have a pair of these ICON pliers that I tried. Great tool, very useful, just not for this job? Also have a much smaller one, similar to the jewelry ones that you linked to. I might give them a tug as well. 11 in., 45° Long-Reach Pliers (harborfreight.com)

The reason I keep trying is both knowing that other people did it, and knowing I did it on a wrangler.

I hope you are joking but after today's total lack of success and bloody mangled fingers I am almost of the belief you are not joking. My Wrangler JLUR was a PITA the first time I did it, but after about a half hour or so of some wiggling and jiggling for each connector, I got them off...

How far from Jacksonville are you? A quick trip to Georgia might be in my future.:LOL::beer: