Search results

Aux 1: Light bar (Diode Dynamics Stage Series 50”) Aux 2: Ditch lights (KC G34’s) Aux 3: Scene lights (KC C2’s) Aux 4: Chase lights (KC Flex single with amber covers)

Cleaned up the rats nest of wires around my battery by adding another fuse box and busbar, then organizing everything onto a PowerTray, including the MPPT Controller for my Cascadia solar panel.

I used these spacers that I ordered from Etrailer.

Desert dweller, where the temps can be really high during summer months. I use both Rotopax (2 mounted to a Leitner rack) and a 5 gallon metal can from Harbor Freight for those longer trips like into the interior of Death Valley. Other than the occasional burping as mentioned, neither has been...

As initially mentioned, it depends on what you’re trying to accomplish. I personally chose to add mine to the engine bay as my purpose of adding a fuse block to my JTR (which has the factory AUX switches) was to clean up the rats nest of wires already in there. The best solution for me was a...

If I may chime in, I had ordered this rack to mount it up front as well. Upon viewing the mounting instructions video on the JCR site, it referenced that the short rack ships with two “R” mounts, whereas the full has “F” and “R”, as in front and rear. I reached out to JCR at that point with my...

The Lotus is a sweet ride, and a nice complement to your JT. I’m quite jealous sir!

Coyote Enterprises deflators to air down, then a Viair 400P compressor with Speedflate 4x system to air up.

Rhino Rack folding aerial bracket for my WeBoost antenna.

Basically echoing what’s been said. I got my dog when he was 4 months old, and at the time he was reluctant to get into any vehicle. Started using treats, and going to destinations that were fun for him (parks, hiking trails, etc.). As we started doing longer road trips, I saw that he would get...

Power Tray with corresponding accessory bundle. Not a fun purchase as its under the hood with no performance improvement, but it’ll drastically clean up the rat’s nest of wires I currently have.

Installed MetalCloak hinge steps. Much easier than I had expected it to be. I read a lot of posts where bolts were stripped, the new bolts were difficult to thread, etc. A few tips for anyone looking to do this with either the MetalCloak or Smittybilt steps: Use a breaker bar. Use a good...

Watching. This is gonna be so rad. Aussie 4x4 builds are by far my favorites.

Mounted a Pelican BX90R Cargo Case to my Rhino Rack Pioneer platform using the Pelican universal roof mounts. Super clean and secure mounting system.

Installed a Diode Dynamics 50” Stage Series light bar.

Installed a Rhino Rack Pioneer Platform with gutter mount RL legs. This will serve light duty work holding a Pelican cargo case that will carry bedding and clothes to allow more space while in my RTT. My freedom tops never come off, so no loss there for me.

Installed a 36” x 56” Pioneer Platform and attached it using the RL gutter mounts. Note, when used with the their leg height spacer system, that I was able to mount this directly to the legs, no other crossbars then the ones that are part of the rack were needed.

This. I had the same happen where I received that message only to find out later while camping that it was running down my main. It fortunately didn’t drain it entirely, just enough to it wouldn’t start but carrying a jump starter saved me. The dealer replaced both batteries as a warranty...

Ditch lights: KC G34’s Chase lights: KC Flex with amber covers Scene lights: Amazon cheapies/KC C-series knock offs Light bar: Diode Dynamics Stage Series 50” with amber covers on each end. Mounted under a Rhino Rack Pioneer platform and set back a bit to avoid glare on my hood.

MetalCloak hinge steps. I’m hoping removing the torx bolts from the hinges isn’t as tough as many reported.