Search results

Proportion? 2.5” JTRD on 37’s I’ve only split 2 pairs of shorts I measured today. To the center if the left drivers thigh bolster, it’s 10” step over width from the rock rail and 40.5” off the ground to the same point. With only a 32” I seem, the old hips have to raise the right butt cheek...

Morning all. I plan on heading up into the Alabama area the week of March 10th. Is anyone planning a ride in the Stony Lonesome? Thought about hitting some trails and grabbing another badge.

When I had mine done it was that you had to be placed in the dealerships list. They make an assessment as to which type of repair is needed. One was just the pump. The second is much more intrusive requiring the pump, fuel lines, injectors…etc. Each dealership has to place you on a list as...

Just a couple quick shots from lunch.

On stock tires I might could see that. In fact I ran 38psi cold. However, on 37x12.50R17’s I’m still beyond the load capacity at 26psi. I hate the chalk test and the one I just did supports my hatred of it. The best I could guess was 31psi with just the last 1/8th of the outside edge being...

I hate to touch this again, but I’m looking for a starting point from those that have done it. Siri was no help. Tire pressure: I ran the following numbers (picture) and came up with 26psi, but it has a disclaimer, which makes perfectly good sense. For optimal wear what have others found...

I shot Benny @AllMoparParts.com note inquiring the cost to shoot me one this morning. The light strip should be here for a weekend quick install. If I don’t like it, it’s an $11 lesson learned.

Good morning Benny Apparently, it’s my turn for the center high mounted third brake light. I have a 21JTRD. The shipping ZIP Code is 32024. What can you do on it? While I’m at it, it would seem that my windshield washer tank pump or lines are clogged. I’m only getting a dribble. Does the tank...

A whole $11.38. I’m gonna clip the wire for the running light or wire it to the bed light and use it as a chase light.

Do you have anything specific that you’re looking for angle wise or poke wise?

Mine didn’t require any additional holes to be drilled. The fronds did however require 3 3/8 Philips head screws. The factory rivet locations all lined up. these are for the high line fenders only… They may have them for the lower fenders. https://a.co/d/5xF7JCL looks like Van_Tri and...

Got new shoes and socks for the weekend. Extended flares two front then two rear measurements

I've got to update my thumbnail pic...she's looking puny with the sagging stock springs under the oil burner...LOL I'll also add, the Clayton kit provides an awesome ride. Absolutely should have increased the spring rate in the factory springs from the start and they screwed it up the second...

I'll say this, whether it means anything, at the first place, he said he activated them, which I believe he did as he had all 4, then added the fifth. It probably was an hour after that when I left, so maybe they timed out. The tech in Valdosta, activated them in the wheels after his test...

So if you do a 5-tire rotation and move the spare to the rear passenger, it still picks up the one you placed under the bet filling the place of the new spare? ...meaning the system still picks it up?

Result… The 2nd location in Valdosta found that none of the sensors were installed were activated. He turned them on and now the TPS is working. Now I have to get the sensor reinstalled in the spare unless someone here can tell me the system doesn’t pick up a 5th sensor.

Thanks! Rokblokz are on the list for the front. I’ll look at the JScan. I’ve had my Tazer Mini for about 2 months and didn’t want to install until 1. I got closer to my factory 36k and lift-tires and wheels were installed. Attempted to install and with a combination of a jacked shoulder...

Thanks for the messages above. I’ll read them better when I have a chance to stop, but I’m heading back from Georgia. Well, I was in Valdosta. I stopped by the discount tire there and spoke to Stephen, and he took his scan to out and found out that the centers were not activated even though the...

LMAO A good indicator as to if your local dealer is modification friendly is when you go ask them how much time it would take and what would it cost to update the computer tire size. Service underwriter comes back after asking one of the techs and without walking up to the jeep and without...

I’m back up at the tire dealer. None of the sensors are working a TPS sensors. So they initially said it needs one factory sensor or I have to go back to the factory and have them back to the dealer and have them do something to it. Or I could go back to the house and pick up the spare and they...