Search results

If I am being honest, I have even saved every bolt, nut or screw I have removed and didn't need to put back on. All together for safe keeping. Lol

I feel like the DV8 JK/JL adapter brackets may have provided enough clearance for you. They are meant for mounting a JK bumper to a JL but could pretty easily be used for your scenario. They mount between the frame and the bumper mount and push the bumper forward about 2in...

I have an iPhone so I can’t speak to the Android Auto question. You can change the default launcher but, without hacking, you cannot uninstall the launcher included in the radio. What other things are you wanting to uninstall?

I don't want to dog on the Ecodiesel, I had a 2018 Ram ED. However, the failure rate scared me out of that truck. It's this lack of trust that would prevent me from buying another vehicle with that engine. I love the engine, I just don't trust it enough to take the gamble. Keep in mind that the...

You can use any switch, the Aux switches just make the wiring easier.

I just ordered this one. We shall see how it goes once I get it in. Amazon.com: PLIOSAUR 500A 12V Winch Solenoid Relay for 8000-15000lb ATV UT Trucks Winches Replacement : Automotive

I ran mine through the firewall and then through the wiring channel along the doors. You can YouTube Gladiator Amp install and you should get some ideas.

Yes, I removed the tray and it sits exactly where the tray did. I have not bolted it down and it hasn’t moved.

These vehicles, like most modern vehicles, use a data bus to monitor circuits. This is called CANBUS. When a circuit is detected as out of spec, based on programming in the BCM(body control module), the diagnostic results in the bulb out message you see in the cluster. In some cases, turning off...

You will want to turn off the diagnostics and May need to use some resistors to create the expected load for the BCM. if you turn off the diagnostics, it may take a couple of key cycles to have the change take effect.

Here are some daytime pics.

I can take pics of the outside. The build quality of these is solid. I was amazed at how much they actually weigh. They are far more durable than the OEM pieces and the entire backside is some type of acrylic or epoxy compound. I have the RGB version so the non RGB version is probably a bit...

XKGlow is a well known brand. They make very heavy duty Marine lighting and their controllers are some of the best out there. I only have a daytime picture with the light off. I will get one with the turn signal in the daytime.

I have seen mention of these headlights on here and wrangler forums. But I figured I would post a thread here with some videos and my observations while installing them. First, these are the headlights I purchased: Tykick 9 Inch Jeep LED Headlights...

I recently installed a set of XKGlow side markers. They replace the black plastic vent on the front fenders. They come in a simple running/turn or running/turn/RGB configuration. I went with the RGB version because I was able to get 25% off on that model. The install is pretty involved because...

I hear you. But I have run LED bulbs with exposed fans and never had a fan failure. I think it will depend on the quality of the component and how well the enclosure is engineered. Time will tell. When I ordered them, I did not see any mention of a fan for cooling. It was stated as built in...

It’s always a matter of opinion, but my opinion is that the only Ford that would compete with a Gladiator is a Bronco Truck. Removable roof and doors are required to truly be competitive for me. I have owned three Ford Rangers over the years and I am not hating on them. I think this will...

Based on that, it would seem that on 21+ models, the LED harness would actually work.

This is copied from the post linked by OHJeeper: It's true. I just wired up some SS5's and wanted the backlights to come on when the halos did. I searched around and found some information: I confirmed that pin #5, labeled as "RIGHT FRONT PARK LAMP DRIVER" is the feed to the halo, which is a...

That is great info. I wish I had found that by searching before I installed these. I basically had to figure it out by trial and error. So that pin 5 is configurable in the BCM as “Signature” lighting. Also, to me that wire looked light brown, but it’s definitely beige looking at the picture...