Search results

For real though, I knew about a year ago it was on it's way out but used the NOCO and got some more time out if them the the writing was on the wall so grabbed the new Aux from the dealer and a new AGM main replacement from a local source. Then the remote start syarted acting up everytime when...

So my issue is on a 2021 80th Anniversary. Backed in ti some snow the other day to turn around on a back road the other day and rear wheels spun even though I had it in 4wd Auto. The dash and offroad pages said I was in 4wd Auto. Of course wlmy winch was froze and when I went tonuse it the...

I bought this unit in 2023, its a 202180th annoversary and it came with an extended warranty with 10 free oil changes. So even though i normally do my own, I figured why waste them. This was the 5th. Picked it up drove 16 kms just out sode of town and the engine light goes on. Codes for oil...

Since I can't delete this thread I guess photos to come once I get to my laptop. Site is super annoying never letting me post pics from my phone. After market wheels are 8.5" wide with 0 offset

Just got my "MOPAR" tranmission filter I ordered. Took it out if the Mopar box, with the Mopar part # sticker on it and look at the filter. It says Filtran right on it. I assume the stock one should say Mopar and NOT Filtran, right? Or am I wrong?

Just curious and haven't seen this mentioned in any searches. In a ZF 8 Speed (well, more specifically the ZF 8 speed in a BMW X5 which has a 'plastic' pan) They tell you to replace the pan bolts when changing the transmission fluid as they are "torque to spec" or like a stretch bolt, those...

Hey, I was given a link and sent this way. I'm lookingto confirm which axles are the correct part #'s for my 80th. Anniversary Gladiator. I've found a couple different #'s that say fit but some look to not be the CV's currently on the vehicle. Im specifically looking for the front right...

I have a 2021 80th Anniversary. 3.6L front 210 axle (rear 220 ). I have a right front axle boot that is cracked open. It goes in tomorrow to see if they will cover under an extended warranty that came with it when I bought it used and told them I wasn't paying extra for a warranty. They ended...

So kinda... just installed my Frankenstein parts. Swapped out the 2.5" spacers and shock extensions on my unit, (didn't know it was there when I got it, thought it was stock...) 2021 80th Anniversary JT. Removed the 2.5" spacers and stock coils. Replaced with MOPAR 2" coils, lower isolators...

I'll keep this as short as possible and try to cut to the chase. Is there stock in the US for sku #355920? It's a Toyo Open Cpuntry AT3 in a 6 ply C range. Im finally at the stage where I am possibly getting my money back on a bad deal with a well known large company up here North of the US...

I had thought my mind was made up on a taller skinnier tire when the time comes. Decided on the 35 11.5x17 Toyo AT3 (sku 355920) Toyo site shows it weighs 62.6 lbs. Then I'm bored reading through threads aimlessly soaking in info (typical mistake for the wallet) and see that the 35x12.5x17...

Looking to make some changes on the cheaper route vs what I have now. Wondering if someone that has a Mopar 2" kit can measure their front stab links and let me know? I found a measurement someone posted on here for the rears being 13" center to center but nothing for the fronts. I have...

I have a 2021 80th Anniversary. I'm wondering if anyone that has a stock unit (or took measurements when they did for the axle to coil bucket? AND if possible, anyone with a Mopar 2" lift can give me some measurements for theirs too. Looking for measurements from top of axle to coil bucket...

Long story short, apparently I have an "aftermarket 2" to 2 1/2" lift. Took some pics for reference. I went and toon a look and There looks to be a 2.25" (Ima call it a 2" spacer) on the top of the coil spring. The, what I'm gona call, the lower bump stop spacer, looks to be like a silver...

Well here it goes again.... Recently found out my stock Gladiator I bought less than a year ago 'slightly' used low mile didn't have stock suspension. Looks to have a 2"-2 1/4" spacer above the front coil, a shock extension and I'm going to assume it must have a longer stable bar link (that is...

So my 21' 80th anniversary is at the dealer for 1 of 9 remaining free oil changes and because I had my first experience with what I'm assuming was the "death wobble" they are inspecting that. I bought this thing last July used with low mileage (37.000 kms) and currently only have 47,000 kms...

Just curious is driving around the only way ti reset the sensors (when installing mew wheels with new sensors)? I just got some new wheels to install the old BFG's I have on for now until I wear those out. Got some new tpms sensors (did my homework, got the correct ones as far as I can tell -...

I'm looking to install an aftermarket winch bumper with fog lights preinstalled. I don't wamt to cut off the connector from the stock bumper but I want a plug and play connector to wire the aftermarket lights on the bumper to that plugs in to the frame side fog light harness on my 21' 80th...

So, I'll get straight to the point. Heres the twist... Whats your thoughts on the best bang for the buck winch you got? BUT... for guys that actually use it, REGULARILY? If its on your Jeep because it looks cool or for a just in case but I only used it once or whatever. That doesn't apply...

So Im new to the Jeep world here. But I'm getting that the rubicon models, Max tow and maybe the Mohave have wider axels (I duno maybe more). So my question is does that mean the entire differential is a wider unit or just the axels themselves are longer but same housing? I assume it is an...