Does anybody offer 1" rear spring spacers?

[AustyPosty]

Hey all, Im putting 37s on my Rubicon soon and wanted to just put a 1 inch spacer front and rear for a few months until I get my full clayton 2.5" lift. However, I cannot find anywhere a 1" rear spring spacer. There's plenty of spacers for the front though.

Sponsored

 

[DailyMoparGuy]

Closest I know of is Icon’s 1-3/8” rear spacer. I run it. It’s nice…no really, super nice to the touch. I’ll probably keep one on my desk once my Clayton lift eventually goes on lol (I’m weird, I know).

https://www.iconvehicledynamics.com/accessory/15822/icon-accessories-icon-2020-2023-jeep-jt-gladiator-138-rear-coil-spacer-kit/

 

[AustyPosty]

Closest I know of is Icon’s 1-3/8” rear spacer. I run it. It’s nice…no really, super nice to the touch. I’ll probably keep one on my desk once my Clayton lift eventually goes on lol (I’m weird, I know).

https://www.iconvehicledynamics.com/accessory/15822/icon-accessories-icon-2020-2023-jeep-jt-gladiator-138-rear-coil-spacer-kit/

Thank you! Ill give this a look!

 

[DailyMoparGuy]

I have a Daystar 3/4. Should be plenty out back
https://www.quadratec.com/p/daystar/34-rear-comfort-ride-spacer-lift-kit-jeep-gladiator-jt

I completely forgot that I had those before the icon ones lol.

 

[PuddleJumper]

Hey all, Im putting 37s on my Rubicon soon and wanted to just put a 1 inch spacer front and rear for a few months until I get my full clayton 2.5" lift. However, I cannot find anywhere a 1" rear spring spacer. There's plenty of spacers for the front though.

I just put a day star 3/4 on my Mojave to get it back to stock ride height with all my gear. It fits a 37 just fine.

 

[AustyPosty]

I just put a day star 3/4 on my Mojave to get it back to stock ride height with all my gear. It fits a 37 just fine.

are you running any lift (or additional bump stops) in addition to the spacer? Im just wondering how well 37s and virtually no lift will work out for me in the short term.

 

[PuddleJumper]

are you running any lift in addition to the spacer? Im just wondering how well 37s and virtually no lift will work out for me in the short term.

No lift sir. I will say the rubicon does need more front then the Mojave though. My rubicon rubs like mofo on the front of if I use the sway disconnect. Mojave doesn’t have that and appears to tuck a bit less. So no lift on the Mojave works fine. Either that or get some bumpstop spacers for the Rubi to hold ya over.

 

[CanHydroGlad]

are you running any lift (or additional bump stops) in addition to the spacer? Im just wondering how well 37s and virtually no lift will work out for me in the short term.

37s will be a tight fit. Top picture is 35 x 11.5(measure 34.5) no lift and bottom is teraflex 1.5 up front and daystar 3/4 in the rear. Good for 35s but maybe not 37s.

 

[chr15m]

Hey all, Im putting 37s on my Rubicon soon and wanted to just put a 1 inch spacer front and rear for a few months until I get my full clayton 2.5" lift. However, I cannot find anywhere a 1" rear spring spacer. There's plenty of spacers for the front though.

https://eibach.com/product/E30-51-024-02-02?epsid=2228

Eibach +1" rear coil, I picked up a set on Black Friday. Havent installed yet, but wanted slightly higher spring rate and closer to 1" than my .75" Daystar spacer.

Sponsored