Mopar halogen led tail light swap

[trader979]

Quick question, swapping oem halogen tail lights for led. I’m going to install them at home and bring to the dealer to flash. Is there anyway they can get damaged using them before flashed?
Thanks

Sponsored

 

[trader979]

Essentially am I just going to get a bulb out or hyper flash? I just don’t want something heating up.

 

[Jefe1018]

It'll either hyperflash or just stop working after a bit.

Curious what you're paying the dealer to do it?

You can get the following plus the $30 for JSCAN and be done with it for $100 and have a tool you can use for any and all changes you might need to make.

https://www.amazon.com/TONWON-vLink...8897&sprefix=tonwon+vlinker+mc,aps,100&sr=8-1

https://www.amazon.com/TTXSPP-Adapt...9Y2xpY2tSZWRpcmVjdCZkb05vdExvZ0NsaWNrPXRydWU=

 

[trader979]

On the way to the dealer today everything was working fine even without flashing the BCM. Picked it up after the dealer flash and now says FRONT left blinker out (with hyper flash). If I only swapped out the tail lights for leds and the dealer flashed the computer, how am I getting FRONT left blinker out? Oh well, back to the dealer tomorrow.

 

[XraytecH]

On the way to the dealer today everything was working fine even without flashing the BCM. Picked it up after the dealer flash and now says FRONT left blinker out (with hyper flash). If I only swapped out the tail lights for leds and the dealer flashed the computer, how am I getting FRONT left blinker out? Oh well, back to the dealer tomorrow.

You'll be doing the back and forth with the dealership. I would suggest getting a TAZER and doing it yourself.

Are your front blinkers LED also?

 

[trader979]

No

You'll be doing the back and forth with the dealership. I would suggest getting a TAZER and doing it yourself.

Are your front blinkers LED also?
[/QUOT

You'll be doing the back and forth with the dealership. I would suggest getting a TAZER and doing it yourself.

Are your front blinkers LED also?

no that’s what I don’t understand. They have always treated me well and I had to have other service done. That’s why I had them do it. Just don’t know why programming the rear leds affected the left front halogen turn signal.

 

[trader979]

Now both front turns are indicating out and hyper flashing. Would jscan or tazer worked better than dealer programming???

 

[SaplingT]

If you only did a bulb swap you probably didn't need to do any reflash.

 

[ShadowsPapa]

CBC Features:
___________________
Tip Start Enabled: Yes
Dual Start Relay System Present: Yes
Wiper Service Position Enabled: No
Fuel Door Release Enabled: No
Trailer Tow Present: Yes
LED Reverse Lamps Present: Yes
LED Stop Lamps Present: Yes
LED Rear Turn Lamps Present: Yes
LED Tail Lamps Present: Yes
LED Rear Fog Lamps Present: Yes
LED License Lamps Present: Yes
LED Front Turn Lamps Present: Yes
LED Front Fog Lamps Present: Yes
LED Dedicated DRL Present: Yes
LED Low Beam Lamps Present: Yes
LED High Beam Lamps Present: Yes
LED Front Park/Marker Lamps Present: Yes

..............................

CBC Extern.Light Calibr.:
___________________
Signature Light Present: Yes
Dual Filament Headlamp: No
Front Turn Lamps Diagnostics: Yes
Auto Headlamp On Threshold (0-5 V): 3.314 V
Auto Headlamp Off Threshold (0-5 V): 2.549 V
Left Side DRL Voltage Target: 11.0 V
Right Side DRL Voltage Target: 11.0 V
Left Low Beam Voltage Regulation: 13.4 V
Left High Beam Voltage Regulation: 13.4 V
Right Low Beam Voltage Regulation: 13.2 V
Right High Beam Voltage Regulation: 13.2 V
Left Front Corner Voltage: 13.4 V
Right Front Corner Voltage: 13.4 V
Left Rear Corner Voltage: 13.6 V
Right Rear Corner Voltage: 13.6 V

There's likely other settings I haven't logged yet.

 

[trader979]

Sorry, I installed a mopar led takeoff tail light.

 

[drew0622]

Check out this video.....took him awhile, but fixed the issue. Sorry if it's not exactly the same as your situation.

 

[trader979]

Sounds like my issue, thank you.

Sponsored