New Product Ideas - We want to hear from you!

[IAG Off-Road]

Thanks everyone for your support so far on our EZ-Steps! We're really happy to see them getting out into the community and we've gotten great feedback so far.

At IAG Off-Road we are are a fully equipped fabrication shop with lasers, benders, brakes, welders, CNC mills and lathes and a variety of other manufacturing equipment. We'd love to hear your ideas for a product that doesn't exist in the Jeep market, or for products you wish were done better. Please use this thread to post new product ideas you want to see us make.

Sponsored

 

[PuddleJumper]

Offset brackets for ditch lights that still allow the windshield to fold forward. Make sure to have a 392/mojave hood version too. A stealth light bar bracket that allows the individual to source their own light bar and not cost 400-800 bucks.

 

[JeepDad74]

design a bracket to accommodate a ditch light or similar to mount on the OEM bracket here

 

[Mtmannh]

Better Mollie panel styles for roof. No place for mounting of ham or gmrs radios on the dash, so overhead is the only option. Amazon Chinese ones are good, but flex too much off road if you have heavy equipment.

 

[DesertDog]

I feel like this one should be easy.
My JL soft top retracts DOWN! When it gets cold or wet, you put the top UP.
I can’t see why the Gladiator soft top can’t have a bracket like the JL so you can actually put the top down without having it stick way up in the air doing the man bun look.
I would love to be able to park in my garage without fiddling
I understand it would possibly interfere with things in the bed, but, holy crap, I think we can figure it out.

 

[FL Robert]

Rear shackle mount to replace the rear hooks. This should be so easy! Why has it not already been done?

 

[Bad software gladiator]

Thanks everyone for your support so far on our EZ-Steps! We're really happy to see them getting out into the community and we've gotten great feedback so far.

At IAG Off-Road we are are a fully equipped fabrication shop with lasers, benders, brakes, welders, CNC mills and lathes and a variety of other manufacturing equipment. We'd love to hear your ideas for a product that doesn't exist in the Jeep market, or for products you wish we done better. Please use this thread to post new product ideas you want to see us make.

6 speed manual drama!
Please hurry! somebody invent a super chip that goes between the PCM and the Ecm on the Jeep gladiator Mojave that will disconnect the PCM from the ECM so my jeep doesn’t constantly go into limp mode when I switch gears to low range in transfer case!

 

[PuddleJumper]

Rear shackle mount to replace the rear hooks. This should be so easy! Why has it not already been done?

it has

 

[PuddleJumper]

6 speed manual drama!
Please hurry! somebody invent a super chip that goes between the PCM and the Ecm on the Jeep gladiator Mojave that will disconnect the PCM from the ECM so my jeep doesn’t constantly go into limp mode when I switch gears to low range in transfer case!

Z automotive NoLimitz module.

 

[FL Robert]

it has

Gee, that's helpful.

 

[MattHamilton]

I swap the hard top and soft top every spring/fall. I'd love a chase bar that accommodates the Mopar Soft roll up tonneau cover, and can easily separate from the bed of the truck at around the height of the bed level, allowing easy top swapping. Assuming the bar has lights (side facing like DV8, plus rear and forward), some kind of quick disconnect at the same location would be required. Of course it needs to be hardy enough to actually support cargo as a tie down point. And look amazing - not like half of a bed rack.

 

[PuddleJumper]

Gee, that's helpful.

i was still looking for the manufactere to get ya a link but they are discontinued. so yeah carry on sir

Sponsored