Roll-n-lock installed

[Vegas_Blue]

I installed the Roll-n-Lock M-Series this last week on the JT. Pretty easy install, just had to use the provided shims to square it up and get the rails horizontal. So far I really like it. Operates flawlessly. Seems like good quality. Time will tell. I’ve attached photos showing measurements that I couldn’t find anywhere on the internet or YouTube. Hopefully the photos speak for themselves, but if anybody needs a specific measurement I’ll try to accommodate.

next up in the immediate future:
-Clayton 2.5 or 3.5 overland plus (ordered-should arrive in a couple weeks)
-37s (likely Nitto RGs) on 17’s (or maybe 18’s)
-Fox2.0 PS IFP shocks
-F/R Axle truss
-front stubby bumper w/winch
-lower profile bed rack system (nobody makes one that I’m envisioning. So I may have to talk to a fabricator).

Sponsored

 

[am1978]

I did the same, except my Roll-n-lock has a Rugged Ridge logo on it—both are owned by the same parent company. I didn’t end up needing the shims though and I waited to install until after I had the line-x sprayed in. Can you snap a pic or two of the shims?

 

[Vegas_Blue]

I did the same, except my Roll-n-lock has a Rugged Ridge logo on it—both are owned by the same parent company. I didn’t end up needing the shims though and I waited to install until after I had the line-x sprayed in. Can you snap a pic or two of the shims?

Sorry for the delay. Here you go. They are about 1/16” thick. On a side note, I’m in traveling in Tennessee and it’s rained everyday. The cover keeps virtually all the water out. Very pleased with it so far.

 

[am1978]

Sorry for the delay. Here you go. They are about 1/16” thick. On a side note, I’m in traveling in Tennessee and it’s rained everyday. The cover keeps virtually all the water out. Very pleased with it so far.

Yep. It rained on me for about 100mi of a 600mi trip earlier this month. Had a full load of vacation gear, luggage, etc. All dry in the bed. I like this cover and it retracts into a space much smaller than my old retractable on my 5.5’ F-150 bed (early lost another 4-5” in the bed for its housing.

 

[BRMoose]

I installed mine about a month ago...waiting for the rebate

I just fed the drain tubes through the holes in the side by the D rings

Drains well and keeps the bed virtually dry

 

[am1978]

I installed mine about a month ago...waiting for the rebate

I just fed the drain tubes through the holes in the side by the D rings

Drains well and keeps the bed virtually dry

Got my rebate on that and for another RR product. Took about 5 weeks. Chose the JT floor mats and a set of JL floor mats since I had two offers to redeem. Sold them both for close to 50% off retail since I didn’t need them, so I figured I’d help some people out who might want them.

 

[KAExcaliber]

Will these work with the mopar trail rail system?

 

[Vegas_Blue]

Will these work with the mopar trail rail system?

I think they have an option with or without. I chose the “without” option.

 

[am1978]

I think they have an option with or without. I chose the “without” option.

This is correct.

 

[KAExcaliber]

Where do you find these Rugged Ridge rebates?

 

[tysongladiator]

I installed the Roll-n-Lock M-Series this last week on the JT. Pretty easy install, just had to use the provided shims to square it up and get the rails horizontal. So far I really like it. Operates flawlessly. Seems like good quality. Time will tell. I’ve attached photos showing measurements that I couldn’t find anywhere on the internet or YouTube. Hopefully the photos speak for themselves, but if anybody needs a specific measurement I’ll try to accommodate.

next up in the immediate future:
-Clayton 2.5 or 3.5 overland plus (ordered-should arrive in a couple weeks)
-37s (likely Nitto RGs) on 17’s (or maybe 18’s)
-Fox2.0 PS IFP shocks
-F/R Axle truss
-front stubby bumper w/winch
-lower profile bed rack system (nobody makes one that I’m envisioning. So I may have to talk to a fabricator).

My dad and I both had them on our Rams. Best bedcover type we ever owned.

Sponsored