Sponsored

Wiring help

Caidenlm

New Member
First Name
Caiden
Joined
May 8, 2021
Threads
1
Messages
3
Reaction score
0
Location
Seneca sc
Vehicle(s)
2020 Jeep gladiator overland. 1987 Jeep Comanche
Occupation
Self employed
Can someone please help. I need to know if there is a replacement for this wiring “harness” (pictured below) I kind of did a half Ass job with the loc and want to do it again a lot nicer. It’s on the right middle door post it’s the one under the seat belt
Jeep Gladiator Wiring help E63733D4-F0A4-4006-BB24-75E586980E0A
Jeep Gladiator Wiring help F2AD29EC-F1CB-4E60-9F6D-FF579FDDD05F
Sponsored

 

Renegade

Well-Known Member
First Name
Zac
Joined
Sep 11, 2017
Threads
38
Messages
3,615
Reaction score
4,816
Location
Signal Mountain, TN
Vehicle(s)
2020 JT
Build Thread
Link
You’re tapping into the speaker system there? Not sure why you’ve used wire nuts (home electrical product), but what exactly do you want to do from here?
 
OP
OP
Caidenlm

Caidenlm

New Member
First Name
Caiden
Joined
May 8, 2021
Threads
1
Messages
3
Reaction score
0
Location
Seneca sc
Vehicle(s)
2020 Jeep gladiator overland. 1987 Jeep Comanche
Occupation
Self employed
You’re tapping into the speaker system there? Not sure why you’ve used wire nuts (home electrical product), but what exactly do you want to do from here?
That’s what I was saying is I did it the first time shity in a rush and now I was wanting to redo it so I was wondering if there was a replacement for just that harness I looked and couldn’t find it
 

SelfmodJT

Well-Known Member
First Name
Jon
Joined
Jan 20, 2021
Threads
32
Messages
683
Reaction score
771
Location
Pennsylvannia
Vehicle(s)
2021 jeep JT Willys, 2005 350z con
Kind of??? You dont need a new wire harness, just solder and heat shrink your wires. Of course you could purchase a new wire harness but i doubt itll be cheap.
 
OP
OP
Caidenlm

Caidenlm

New Member
First Name
Caiden
Joined
May 8, 2021
Threads
1
Messages
3
Reaction score
0
Location
Seneca sc
Vehicle(s)
2020 Jeep gladiator overland. 1987 Jeep Comanche
Occupation
Self employed
Kind of??? You dont need a new wire harness, just solder and heat shrink your wires. Of course you could purchase a new wire harness but i doubt itll be cheap.
Yes because for the five wires I had to do three of them I had enough stuff for and then I ran out so that’s why I used the wire nuts and I just got some Tessa tape so I was wanting to go redo it and I’m going to fix the wire nuts but instead if I could find a new harness I was going to redo the whole thing to where you couldn’t tell I did anything If that makes sense
 

Sponsored

AllMoparParts.com

Summit Sponsor (Level 3)
First Name
Benny
Joined
Sep 16, 2019
Threads
15
Messages
1,810
Reaction score
1,170
Location
New York
Vehicle(s)
JT's!
Can someone please help. I need to know if there is a replacement for this wiring “harness” (pictured below) I kind of did a half Ass job with the loc and want to do it again a lot nicer. It’s on the right middle door post it’s the one under the seat belt
E63733D4-F0A4-4006-BB24-75E586980E0A.jpeg
F2AD29EC-F1CB-4E60-9F6D-FF579FDDD05F.jpeg
This may be part of the body harness. Please send me your VIN and clarify this location, I will check for a replacement.

- Benny
Sponsored

 
 







Top