Leveling the Mopar lift...

[pmontague1968]

Anybody know what size spacer would level the Mopar 2" lift? RC has a .75" puck...that seems a little small...Thanx!

Sponsored

 

[Sal]

Anybody know what size spacer would level the Mopar 2" lift? RC has a .75" puck...that seems a little small...Thanx!

The Mopar lift doesn’t need a leveling kit.

 

[pmontague1968]

The Mopar lift doesn’t need a leveling kit.

I know it doesn't NEED one, but I'd like to correct the rake...

 

[Sal]

There shouldn’t be a rake. The rear springs/socks are the same size as the front

 

[Jeepers!]

There shouldn’t be a rake. The rear springs/socks are the same size

The lift doesn't keep the rake? What about hauling and towing?

 

[pmontague1968]

There shouldn’t be a rake. The rear springs/socks are the same size as the front

My front end is definitely a good bit lower than the rear

 

[pmontague1968]

So, I measured and it's 2.5" lower in the front...is it safe to add a 1.5-2.5 inch puck to the Mopar lift? Thanx

 

[Jeepers!]

So, I measured and it's 2.5" lower in the front...is it safe to add a 1.5-2.5 inch puck to the Mopar lift? Thanx

I'd keep some rake if you want to tow or haul anything

 

[beelzebot]

So, I measured and it's 2.5" lower in the front...is it safe to add a 1.5-2.5 inch puck to the Mopar lift? Thanx

The lift left me a solid 2" of rake. I installed a 0.75" spacer in the front. Looks much better and still retains some rake for when I'm hauling so it doesn't sit too low in the rear. It did pull my front axle off center a little more than it already was from the lift so an adjustable trackbar is probably in my future. It's not that bad and won't cause any problems but I'm a little too scrupulous. It'll be a good excuse to recenter my steering wheel too because it's just barely off.

 

[Ted Striker]

The lift left me a solid 2" of rake. I installed a 0.75" spacer in the front. Looks much better and still retains some rake for when I'm hauling so it doesn't sit too low in the rear. It did pull my front axle off center a little more than it already was from the lift so an adjustable trackbar is probably in my future. It's not that bad and won't cause any problems but I'm a little too scrupulous. It'll be a good excuse to recenter my steering wheel too because it's just barely off.

Yep. I did the same thing. Added a 3/4" spacer on top of the Mopar lift and then bought a JKS adjustable track bar to re-center the axle and used the opportunity to re-center the steering wheel.

 

[Joker4L]

I have zero rake after my mopar lift. My rubicon is perfectly leveled when measure from thread to fender well or even from the ground to the fender well.

 

[Sal]

So, I measured and it's 2.5" lower in the front...is it safe to add a 1.5-2.5 inch puck to the Mopar lift? Thanx

i added a winch and and new steel bumper and I lost 1.5 in. So I understand your issue now :/

 

[Southbayglad]

The Mopar lift doesn’t need a leveling kit.

The lift left me a solid 2" of rake. I installed a 0.75" spacer in the front. Looks much better and still retains some rake for when I'm hauling so it doesn't sit too low in the rear. It did pull my front axle off center a little more than it already was from the lift so an adjustable trackbar is probably in my future. It's not that bad and won't cause any problems but I'm a little too scrupulous. It'll be a good excuse to recenter my steering wheel too because it's just barely off.

Do you have any pics? What spacer did you use?

 

[beelzebot]

Do you have any pics? What spacer did you use?

I'll see if I can grab some pics at lunch. I have a few but none that really show the rake from the side.

 

[JJmoto]

Anybody know what size spacer would level the Mopar 2" lift? RC has a .75" puck...that seems a little small...Thanx!

1.5 Teraflex
Almost perfectly equal ft (8.5) rr (8.75).

Sponsored