Pics Request: Rough Country 2.5” level kit and 3/4” daystar spacer

[Jumperdp]

Wondering if anyone has pics of a rough country 2.5” level kit and 3/4” daystar spacer on the rear. I currently have the teraflex 1.5” in front and my bumper/winch dropped the nose a bit- looking to get a little extra height in front. Worried it might be nose high with the rough country- anyone have pics of this setup? It would be on a 2020 gladiator rubicon

Sponsored

 

[OnlyOne]

Here it is on my Overland with 37s.

 

[Trauma PA]

Probably a little late but this is the RC 2.5” front spacer lift with shock extensions and the rear 3/4” Daystar spacer. Notice I have an aftermarket bumper and winch too and no issues with front end droop or nose sitting higher.
just noticed these pics are without the winch but I do not have any issues with winch installed..

 

[Trauma PA]

Here is with winch

 

[Jumperdp]

Thank you, I have this setup on mine decided to just pull the trigger. I think I’m gonna do a 1.5” spacer in the rear and it should be perfect - also bought the sway bar links from the mopar kit. I’m debating shock extensions, just not sure if they’re needed for 1.5”.

 

[DocMcStuffins]

Very happy with this setup + 1.5" wheel spacers. No rubbing on full-stuff with 37's and that was before fender chop.

 

[Trauma PA]

Very happy with this setup + 1.5" wheel spacers. No rubbing on full-stuff with 37's and that was before fender chop.

Looks good. Which 1.5” wheel spacers did you go with?

 

[DocMcStuffins]

Looks good. Which 1.5” wheel spacers did you go with?

Some brand off Amazon, I think all 4 for $105- I made sure they were hub-centric and torqued properly. I have been on multiple HARD rock crawling and snow trips without issue. Checked them several times between and they were all good. I've read of some snapping the studs off, but then again have seen people breaking axles/knuckles/etc. I agree that it is one more thing to possibly break and it does put more stress on the axle components but just as a lower backspaced wheel would.

 

[glassjawkid32]

Exact Setup with 35s

 

[Jerhemi]

Exact Setup with 35s

Hard to tell from the pics, but is it nose high at all? I like a little rake. Beautiful truck ??

 

[glassjawkid32]

Hard to tell from the pics, but is it nose high at all? I like a little rake. Beautiful truck ??

Thank you. I wanted a slight rake as well. I'm pretty happy with the results, it doesn't look nose high in person to me. I think it's about dead level but the fenders give an illusion of slight rake. I'll try and remember to actually measure tomorrow.

 

[glassjawkid32]

From the center of the tire to the bottom of the fender is: F 5.5 and rear 6"

 

[DailyMoparGuy]

Probably a little late but this is the RC 2.5” front spacer lift with shock extensions and the rear 3/4” Daystar spacer. Notice I have an aftermarket bumper and winch too and no issues with front end droop or nose sitting higher.
just noticed these pics are without the winch but I do not have any issues with winch installed..

Nice build. Did you replace the rear sway bar links or do the factory ones work fine with the 3/4” Daystar puck?

 

[Trauma PA]

Nice build. Did you replace the rear sway bar links or do the factory ones work fine with the 3/4” Daystar puck?

I used the extended sway bar links that come in the RC kit up front and kept the factory in the rear to go along with the 3/4” Daystar puck. No issues.

 

[DailyMoparGuy]

I used the extended sway bar links that come in the RC kit up front and kept the factory in the rear to go along with the 3/4” Daystar puck. No issues.

Awesome. Thanks for the info!

Sponsored