Sponsored

Voswitch and backlighting question

ColoMojaveX

Well-Known Member
First Name
Brandon
Joined
Dec 24, 2025
Threads
5
Messages
66
Reaction score
98
Location
NoCo
Vehicle(s)
2025 Mojave X
Hey folks, quick question to the electrical guru’s out there. I have Harbor Freight off-road lights that are backlit with a fuse tap . I’m installing the Voswitch JL810 and it has a fuse tap for this same reason.
So do I need to wire my wire coming from my lights (yellow wire) in with the wire coming from the Voswitch fuse tap? Or do I need to not wire that yellow wire in at all because the Voswitch module has it for the same reason 🤷🏻

TIA
Sponsored

 

ChrisNLA

Well-Known Member
First Name
Chris
Joined
Jun 7, 2022
Threads
23
Messages
3,543
Reaction score
6,885
Location
Louisiana
Vehicle(s)
2022 JT Sport Max Tow
Build Thread
Link
What is the Voswitch wire with fuse tap for? Is it to provide back lighting to the switch panel?

Unless the Voswitch is outputting a back light signal as well, then you need to connect your off road light backlighting to whatever source you are connecting the Voswitch backlighting to, assuming you want them both to operate the same way.
 
OP
OP
ColoMojaveX

ColoMojaveX

Well-Known Member
First Name
Brandon
Joined
Dec 24, 2025
Threads
5
Messages
66
Reaction score
98
Location
NoCo
Vehicle(s)
2025 Mojave X
What is the Voswitch wire with fuse tap for? Is it to provide back lighting to the switch panel?

Unless the Voswitch is outputting a back light signal as well, then you need to connect your off road light backlighting to whatever source you are connecting the Voswitch backlighting to, assuming you want them both to operate the same way.
The Voswitch fuse tap is if you only want the panel to power on with the ignition. This is the way I had my DRL’s hooked up.

I connected the wire from the Voswitch, and the yellow wire from my lights to the fuse tap……….DRL’s don’t come on at ignition. Lights not turn on at all, but this may be a programming issue on my part.
 

Bandit’s Lair

Well-Known Member
First Name
Jason
Joined
Jul 9, 2025
Threads
54
Messages
4,815
Reaction score
8,266
Location
Southern California
Vehicle(s)
2021 Gladiator Sport S
Occupation
Retired
To my knowledge, you’d have to have the backlights on a separate switch if you want any them on separate from the main lights. The only panels I know of that include a backlight specific function FOR LIGHTS are the Diode Dynamics and the newer AuxBeam dial controller with the Zero fuse. The backlight function of the VosSwitch is only for the control panel backlight.
 

Bandit’s Lair

Well-Known Member
First Name
Jason
Joined
Jul 9, 2025
Threads
54
Messages
4,815
Reaction score
8,266
Location
Southern California
Vehicle(s)
2021 Gladiator Sport S
Occupation
Retired
From Google:

Splice into the Vehicle's ACC/Ignition Trigger: If you want your light bar's backlights to be on whenever the vehicle is running (functioning as DRLs), you bypass the Voswitch block for the backlight wire entirely. Instead, splice the light's backlight wire directly into the same vehicle ignition/ACC fuse tap that triggers your Voswitch control box.
 

Sponsored

OP
OP
ColoMojaveX

ColoMojaveX

Well-Known Member
First Name
Brandon
Joined
Dec 24, 2025
Threads
5
Messages
66
Reaction score
98
Location
NoCo
Vehicle(s)
2025 Mojave X
From Google:

Splice into the Vehicle's ACC/Ignition Trigger: If you want your light bar's backlights to be on whenever the vehicle is running (functioning as DRLs), you bypass the Voswitch block for the backlight wire entirely. Instead, splice the light's backlight wire directly into the same vehicle ignition/ACC fuse tap that triggers your Voswitch control box.
This is exactly what I did. 🤷🏻 I took the yellow wire from the lights, and the wire from the Voswitch and ran them both to the fuse tap.
Apparently the jl810 is suppose to have this ability.
 
Last edited:

Bandit’s Lair

Well-Known Member
First Name
Jason
Joined
Jul 9, 2025
Threads
54
Messages
4,815
Reaction score
8,266
Location
Southern California
Vehicle(s)
2021 Gladiator Sport S
Occupation
Retired
Are you within power specs? If you have another fuse tap maybe try running the backlighting from the lights to another ACC and see what happens. That was my original plan. Bus bar to an ACC tapped fuse and just let that turn lights on once the “key” is turned.
Sponsored

 
 







Top