Sold: Ohio Jeep gladiator pre runner inserts

[theMantheLegend]

Jeep gladiator prerunner light inserts. These fit the oracle lighting pre runner lights for the jeep. They just squeeze into the grill insert. No glue necessary but as time goes on I recommend gluing in some way. I used a small amount of black rtv on the bottom and you can't see it. While they were staying in place car washes would push then trhough the grill.

They are very basic 3d printed inserts. I'll print them in carbon fiber filament which is the black you see. Message me if you're interested.

$25.00 for set of 3 shipped. $10 for each additional one.
PayPal accepted.

No lights included just the inserts.

NOTE: I have checked a few gladiators now, if you have the honeycomb grill as seen in the images these will work for your gladiator.

Ebay lights that work
https://www.ebay.com/itm/283891817689
Oracle lights
https://www.oraclelights.com/produc...adiator-jt?rq=mk_jeep~md_gladiator-jt~yr_2021

Sponsored

 

[Mac]

Very cool, what size is the opening for the light ? I have some led lights already.

 

[theMantheLegend]

22.5 mm I believe is what I made it.

 

[LakeMAnn]

Any chance you would make them for a Mojave hood scoop?

 

[theMantheLegend]

Any chance you would make them for a Mojave hood scoop?

There's a yes and no to that. I don't have a mojavi nor access to one. Now you can send me the dimensions and I can my best to get it right the first time (these took about 9 iterations), you can send me the part and I can make them for you or the answer is no. Sorry I can't be more helpful.

 

[mnf1fan]

Any chance you would make them for a Mojave hood scoop?

Mojave is more complicated as you have to remove the plastic shield behind the hood grill to run the wires. At that point you can simply drill a hole in the shield and insert the LED assy into it. Then the LEDs will also be recessed behind the honeycomb grill.

Just my opinion of course.

 

[ImThe0ne]

This is way more elegant than the giant washers that Oracle sends you. I installed mine 4 months ago and have been too lazy to wire them up....
I might hit you up for some of these in the near future.

 

[Deadpool392]

PM inbound

 

[DMXRacing]

Mojave is more complicated as you have to remove the plastic shield behind the hood grill to run the wires. At that point you can simply drill a hole in the shield and insert the LED assy into it. Then the LEDs will also be recessed behind the honeycomb grill.

Just my opinion of course.

https://www.jeepgladiatorforum.com/forum/threads/mojave-diy-prerunner-lights.38986/#post-631200

 

[theMantheLegend]

https://www.jeepgladiatorforum.com/forum/threads/mojave-diy-prerunner-lights.38986/#post-631200

Those look like the same shape as the willys grill. If the inserts are the same I'd say these would work.

 

[Orange01z28]

Anyone know if the Willys grill is any different than the Sport S grille?

 

[theMantheLegend]

[/QUOTE]
If it looks like the pictures you should be good. My wife's jl sport is different though.

Anyone know if the Willys grill is any different than the Sport S grille?

My wife jl sport grill is different. That's all I have to go off. I'll try to drive through a jeep dealer today and see what these will fit.

 

[theMantheLegend]

Bump

 

[Troybilt]

I think this is a very well done product. I am in Ohio and like to support Ohio folks But I have no idea what Pre Runner Lights are for or represent.

 

[theMantheLegend]

I think this is a very well done product. I am in Ohio and like to support Ohio folks But I have no idea what Pre Runner Lights are for or represent.

Prerunner is a simple way to describe a series of lights going across the grill like you see the green ones above. they are just marker lights basically. Help with visibility.

Sponsored