armd.offroad
Active Member
- Thread starter
- #1
Hey Everyone, long time member / lurker but this is the first time I am reaching out for help. Let's see how this goes...
First, my Issue:
My issue is I get a No Front Turn Signals Error on the dash (see pic below) and the turn signals hyper-flash ON THE DASH ONLY (the turn signal lights themselves (headlights and sidelights) do not hyper-flash. The front turn signal error light on the dash lights up every time I start the Jeep, and the green turn signal arrows hyper-flash on the dash when using the turn signals. I like to use my turn signals to tell other drivers where I am headed and to be as safe as possible because this is my daily driver most of the time. The errors are produced because I am not running any stock turn signals and nothing is plugged into the stock turn signal plug.
More details:
My 2022 Jeep Gladiator Ecodiesel Rubicon (DOBICON.JT on IG) is heavily modified, but I will spare you all the mods that don't relate to this post. The mods that relate to this post are that I am running Nemesis Crawler High-line Fenders, Diode Dynamics Elite Max Headlights with Integrated Turn Signals, and D&C Designs side lights that blink with the turn signals so they provide a side marker light.
I removed the turn signals from the Nemesis Crawler High-line Flares because they are so small they were not noticeable and you couldn't even see them in the daylight because they weren't big enough or bright enough in my opinion and I also didn't like the look or placement of them aesthetically. This is why I decided to run the Diode Dynamics Elite Max headlights instead because they produce a much larger brighter more noticeable turn signal and look 100% better.
I have already tried the following:
1. I have tested hooking up the stock turn signal wiring and lights plugged into the diode dynamics wiring with the current setup and the error and hyper-flashing goes away and everything works as it should. I knew this would work because it is basically like having everything stock.
2. I have also tested the stock wiring plugged into the diode dynamics wiring and wired in the nemesis turn signal and still received the hyper flashing and error on the dash.
3. I have also tested the stock wiring plugged into the diode dynamics wiring and wired in the nemesis turn signal along with a resistor and still received the hyper flashing and error on the dash.
At this point I am at a loss for how to get rid of this No Front Turn Signal Error and Hyper-Flashing on the dash. If anyone has a similar setup or can provide any suggestions at all on how to fix this, I would greatly appreciate it.
Cheers Fellow Jeepers,
-Anthony
First, my Issue:
My issue is I get a No Front Turn Signals Error on the dash (see pic below) and the turn signals hyper-flash ON THE DASH ONLY (the turn signal lights themselves (headlights and sidelights) do not hyper-flash. The front turn signal error light on the dash lights up every time I start the Jeep, and the green turn signal arrows hyper-flash on the dash when using the turn signals. I like to use my turn signals to tell other drivers where I am headed and to be as safe as possible because this is my daily driver most of the time. The errors are produced because I am not running any stock turn signals and nothing is plugged into the stock turn signal plug.
More details:
My 2022 Jeep Gladiator Ecodiesel Rubicon (DOBICON.JT on IG) is heavily modified, but I will spare you all the mods that don't relate to this post. The mods that relate to this post are that I am running Nemesis Crawler High-line Fenders, Diode Dynamics Elite Max Headlights with Integrated Turn Signals, and D&C Designs side lights that blink with the turn signals so they provide a side marker light.
I removed the turn signals from the Nemesis Crawler High-line Flares because they are so small they were not noticeable and you couldn't even see them in the daylight because they weren't big enough or bright enough in my opinion and I also didn't like the look or placement of them aesthetically. This is why I decided to run the Diode Dynamics Elite Max headlights instead because they produce a much larger brighter more noticeable turn signal and look 100% better.
I have already tried the following:
1. I have tested hooking up the stock turn signal wiring and lights plugged into the diode dynamics wiring with the current setup and the error and hyper-flashing goes away and everything works as it should. I knew this would work because it is basically like having everything stock.
2. I have also tested the stock wiring plugged into the diode dynamics wiring and wired in the nemesis turn signal and still received the hyper flashing and error on the dash.
3. I have also tested the stock wiring plugged into the diode dynamics wiring and wired in the nemesis turn signal along with a resistor and still received the hyper flashing and error on the dash.
At this point I am at a loss for how to get rid of this No Front Turn Signal Error and Hyper-Flashing on the dash. If anyone has a similar setup or can provide any suggestions at all on how to fix this, I would greatly appreciate it.
Cheers Fellow Jeepers,
-Anthony
Sponsored
