intentsrig
Well-Known Member
- First Name
- Brian
- Joined
- May 25, 2019
- Threads
- 12
- Messages
- 129
- Reaction score
- 82
- Location
- California
- Vehicle(s)
- JT
Really? Now I’m getting conflicting answers lol
Sponsored
Sponsored
JTRDistraction
Well-Known Member
- First Name
- Christopher
- Joined
- Oct 16, 2022
- Threads
- 1
- Messages
- 151
- Reaction score
- 251
- Location
- Green Cove Springs, Fl
- Vehicle(s)
- 2022 Jeep Gladiator Rubicon
- Occupation
- Utility Substation Electrician
The foil is the radiant barrier and should be placed on the outermost point to reflect the most heat from getting inside. At least that's the theory.
OP
OP
Free2roam
Well-Known Member
- Thread starter
- #199
Measurements
Driver's side
18.5"T *15.5D*56.5
Passenger side
42H (could have been a little shorter)
15.25 D*33.25 long
Front of bed Fridge freezer area
19*38*13.5
Top of counter 34.75L*15D
I did take off the front trail rail section to make a bit more room.
Under fridge freezer area is a 15 gallon water tank.
There is also a sink and grey water tank. Plus 2 100AH Renogy batteries and 400 watts of solar.
Sponsored
WestwallNF104A
Well-Known Member
Looks great!Another piece of the puzzle today on the swing away. Got the backing piece and the mounting piece installed and welded today.
OP
OP
Free2roam
Well-Known Member
- Thread starter
- #205
Just when you think you have it all dialed in! Geezuz really couldn't you have just not galled up and cost me my whole day!??
I was into the last phase of putting the swing away together. I had previously had no issues with the nut
setting up the latch hold open mechanism. Got it figured out. Then Ruh Roh Shaggy!!
I had the induction bolt heater going. Broke out the good tools after that. Mac chisels and the Snap-On ball pein hammer. Quite a few oh fucks later a couple of fuck that hurt and please fucking come offs! After I had heated that nut red hot. Finally broke through the last section. Now it's wait and see if the order from bezos solves the problem. Hardest part is trying to rethread the shaft.
I was into the last phase of putting the swing away together. I had previously had no issues with the nut
setting up the latch hold open mechanism. Got it figured out. Then Ruh Roh Shaggy!!
I had the induction bolt heater going. Broke out the good tools after that. Mac chisels and the Snap-On ball pein hammer. Quite a few oh fucks later a couple of fuck that hurt and please fucking come offs! After I had heated that nut red hot. Finally broke through the last section. Now it's wait and see if the order from bezos solves the problem. Hardest part is trying to rethread the shaft.
Sponsored
WestwallNF104A
Well-Known Member
Oh, that sucks man! I have a friend with a lathe up in Sparks if you need help.Just when you think you have it all dialed in! Geezuz really couldn't you have just not galled up and cost me my whole day!??
I was into the last phase of putting the swing away together. I had previously had no issues with the nut
I had the induction bolt heater going. Broke out the good tools after that. Mac chisels and the Snap-On ball pein hammer. Quite a few oh fucks later a couple of fuck that hurt and please fucking come offs! After I had heated that nut red hot. Finally broke through the last section. Now it's wait and see if the order from bezos solves the problem. Hardest part is trying to rethread the shaft.
WestwallNF104A
Well-Known Member
Ahh, yeah....that's a problem!Unfortunately it's welded to the bumper.
Hindsight......anti-sieze.
MILT
Member
not sure if this is one of you here, but this is from big sky MT last spring at a trailhead. This has caused me to buy a gladiator so I can get this camper.
WestwallNF104A
Well-Known Member
Excellent choice, Sir! Though OVRLND makes them for many different makes of truck.
not sure if this is one of you here, but this is from big sky MT last spring at a trailhead. This has caused me to buy a gladiator so I can get this camper.
Sponsored
