Voswitch JL400 anyone?

[Mball488]

So I noticed that Voswitch has come out with their new JL400 that integrates with the driver grab handle. For the life of me I cannot find any videos of installation or anyone who has actually bought it. Figured this would be the place to ask around!

Sponsored

 

[amoyer_01]

I would think it is like all of their other products under the hood for the install. Then route through the firewall on the drivers side and up to the grab handle. Start at the 3:00 mark for the grab handle disassembly, should be easy enough to find a grommet if you have an auto (manual is harder since that grommet is used). The product is still in pre-order on their site.

The Stinger Heigh10 install video.

 

[Mball488]

Amazon has it already for sale. Couple pictures that make it one of the cleanest switch "panels" around. Love the MOPAR Aux panel, but 4 switches is really the bare minimum for those who actually overland or go off-road at all.

 

[SelfmodJT]

I have it, what questions did you have? They were available months ago btw.

 

[Mr._Bill]

The Twisted Pro TS4 looks identical to the JL400, although more expensive. One of the pictures on their site has a QR code that provides a link to their installation instructions.

 

[SelfmodJT]

The Twisted Pro TS4 looks identical to the JL400, although more expensive. One of the pictures on their site has a QR code that provides a link to their installation instructions.

Yeah 249.99 is a lot and it does seem like theyre both the same unit. I paid 179.99, amazon was discounting $20 dollars when I bought mine.

 

[sass JT]

FYI…

Did you see they also have the JL800???

Voswitch JL800 Grab Handle Switch Panel for Jeep Wrangler JL 2018-current and Gladiator 2020-current https://a.co/d/9f4Mxq1

 

[TheTrailGeek]

FYI…

Did you see they also have the JL800???

Voswitch JL800 Grab Handle Switch Panel for Jeep Wrangler JL 2018-current and Gladiator 2020-current https://a.co/d/9f4Mxq1

I love the extra switches and features on the JL800, just wish it looked more factory like the JL400. Torn between which one to get just because I don't like the boxy look of the 800.

 

[TheOpa]

I have it, what questions did you have? They were available months ago btw.

I recently bought/installed the J300 because I wasn’t sure how this would look up on the grab handle. Too bad I didn’t see this pic first. Looks really clean and as if it came that way from the factory - those were two of my biggest selection criteria. Nicely done

 

[BAT]

Amazon has it already for sale. Couple pictures that make it one of the cleanest switch "panels" around. Love the MOPAR Aux panel, but 4 switches is really the bare minimum for those who actually overland or go off-road at all.

That and those AUX switches are in a really bad place for quick access

 

[Mball488]

How was the installation on the grab handle? I hope it doesnt require me to take apart half the jeep like my cargo inverter switch did. What a pain!

 

[paclives777]

I have it, what questions did you have? They were available months ago btw.

I just installed lost directions. How do you change color and dim etc

 

[Minty JL]

There you go! Enjoy

 

[Zero_Accel]

I just installed lost directions. How do you change color and dim etc

With the engine OFF (Accessory mode works too), hold the power button down for approximately 3 seconds until the switch turns on. This is the programmable mode. To change the color, press the power button once, to raise the brightness, press switch #1 (Lightbar), to lower the brightness, press switch #4 (Aux 2). To save your settings, wait for the switch to power off on it's own, about 20 seconds.

 

[paclives777]

Doesn’t say a word about how to change it. Also did you hook up the negative to the battery negative or a body bolt?

Sponsored