What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS, NO GUN TALK]

[Jeepmonster]

I replaced a missing air box screw that I dropped when I opened the box to shake the filter out after the last time I went wheeling. I got me a handy T wrench with 1/4" drive on each end. It came with 8mm, 10mm, and 12mm sockets. I just keep the tool in my glovebox for easy access. It is handy for loosening and tightening several items under the hood. I haven't had a need to use the 12mm. Not sure if there are any 12mm bolt heads within easy reach (or any at all).

Update:
Here is the link to the tool. There are others available, but most seemed shorter or only had the drive on one end.
https://www.amazon.com/dp/B004MAGY5Y?ref=ppx_yo2ov_dt_b_fed_asin_title

Sponsored

 

[GlennBeck]

Added driver and passenger side molle panels from Barnes 4WD today.

Love the bronze contrast and solid molle all the way front to back!

 

[GlennBeck]

I replaced a missing air box screw that I dropped when I opened the box to shake the filter out after the last time I went wheeling. I got me a handy T wrench with 1/4" drive on each end. It came with 8mm, 10mm, and 12mm sockets. I just keep the tool in my glovebox for easy access. It is handy for loosening and tightening several items under the hood. I haven't had a need to use the 12mm. Not sure if there are any 12mm bolt heads within easy reach (or any at all).

Worth it for the 10mm alone!

 

[Jeepmonster]

Worth it for the 10mm alone!

Haha, I'm actually thinking of replacing the 12mm with a spare 10mm!

 

[Camaroboi13]

The new fenders look great! How long was the install process?

If you’re referring to mine, 2 hours on the passenger rear dealing with mismatched hardware, then 20 minutes on the driver’s side doing it my own way. The front had some hiccups too, but under 4 hours for all 4 fenders.

 

[Sawburner]

Came out to the truck this morning and when it turned on this was the screen...

Mine did that awhile back more then once, had the dealer make a note of it, they had no idea why, been fine since.

 

[bill61]

I got my Gladiator last week and here is my first mod. It's not much, but I found door lock covers on the interwebs. The site said I should get the set of 6 for a 2024 Gladiator, but I only needed 4. I think there is a design change on the 2024 tailgate latch from a door-like hoop to a single post. Again, I learned something new about my new toy. They are simple, inexpensive little covers, but I think they clean up the door frame a bit.

View attachment 412777

I think if I did that I would get the color matching paint ( https://www.automotivetouchup.com/touch-up-paint/jeep/ ) and make them fully blend in.

 

[bill61]

I replaced a missing air box screw that I dropped when I opened the box to shake the filter out after the last time I went wheeling. I got me a handy T wrench with 1/4" drive on each end. It came with 8mm, 10mm, and 12mm sockets. I just keep the tool in my glovebox for easy access. It is handy for loosening and tightening several items under the hood. I haven't had a need to use the 12mm. Not sure if there are any 12mm bolt heads within easy reach (or any at all).

Hello, do you have a link to that tool? Thanks in advance.

 

[Jeepmonster]

Hello, do you have a link to that tool? Thanks in advance.

Ah, I broke one of the cardinal rules on this forum: pictures AND links. I updated the origninal post with the Amazon link.

 

[bill61]

A couple weeks ago I had the RSE steps installed. I love them so much on my JKU I bit the bullet.
Then yesterday I put non-skid tape on the top of them. The drop down step already has non-skid tape. The tops only had textured paint.

 

[zcashio]

After a few months of ownership I finally washed it. Needed that salt from last weeks single digits and snow to get off, so it’s 60 degrees today and sunny and figured no better time than now

 

[Stan H]

Well, so Saturday I replaced the PCV valve, Sunday after church ,I replaced the crank sensor , I have an upstream oxygen sensor and a new Map sensor on the way as well. I am doing a lot of sensor renewals.
Surprisingly even though the cranksensor had never thew a code etc. After sticking it in I swear up and down it runs better . Like it has more power.

 

[stormshadow]

Changed out the 2024 sport seats for some 2022 Rubicon leather seats. More padding and more comfortable.

 

[Stan H]

Changed out the 2024 sport seats for some 2022 Rubicon leather seats. More padding and more comfortable.

Where did you find some ??

 

[stormshadow]

Where did you find some ??

I found them at lkq online, only had a couple thousand miles on them. very low mile and in great shape. If you use them, call them instead of ordering on line and have them shipped to a local business to save on shipping...otherwise shipping charges are very stupid.

Sponsored