Sponsored

Apex Autolynx anti-sway bar disconnects

bd100

Well-Known Member
Joined
May 31, 2022
Threads
28
Messages
764
Reaction score
746
Location
USA Midwest
Vehicle(s)
JT, WK2, ole' Ram
In prep for a trip I installed the Apex Autolynx disconnects. I chose to seal the snap rings from road salt and water using masking tape and gasket sealer, which seemed to work better than liquid electrical tape.

Assuming that these things last, they completely paid for themselves in that I was able to disconnect the sway bar and provide for my family a softer ride than otherwise. We were able to compare with and without disconnect and they're very happy to have the disconnect. This was their first time offroad and they were worried about all the bumps.

By the way, the stock Sport S shocks seemed fine. I did get some LT tires, though, which greatly reduced the side-to-side swaying, which was largely from the flex of the original street tires. On my first pickup I got whiplash from that after a few days.

And I had the LT tires at 55psi because they were getting pretty warm at 40psi while hauling our supplies and towing our trailer at 75mph. I didn't want to air down on the trails because we were not slipping and I was still carrying a cap and a lot of cargo even without the trailer. And airing back up to 55psi takes a while.

As for articulation and such, it did knock the suspension bump stops a few times when I was going faster than I should have on some largish rocks. But we never spun a tire.

To reconnect, I found it useful to place the palm of a hand on the ledge of the mounting bracket and get close enough to push almost straight down. Sometimes it didn't make a noticeable click on reconnect, but it worked each time.
Sponsored

 

jeepers29

Well-Known Member
First Name
Joel
Joined
Aug 24, 2021
Threads
10
Messages
1,565
Reaction score
2,557
Location
Georgetown Tx
Vehicle(s)
JKUR, GC
Occupation
Domestic engineer
At 55 psi, ibet your kidneys took a beating. I air down to 13 psi when trail riding. Highway we are at factory 37psi.
 
OP
OP
bd100

bd100

Well-Known Member
Joined
May 31, 2022
Threads
28
Messages
764
Reaction score
746
Location
USA Midwest
Vehicle(s)
JT, WK2, ole' Ram
No big deal. The shocks do their work. Whether THEY took a beating is an interesting question, though...
 

Free2roam

Well-Known Member
First Name
Robert
Joined
Mar 1, 2021
Threads
30
Messages
5,489
Reaction score
11,682
Location
89521
Vehicle(s)
Gladiator
Occupation
Fabricator by trade/ Maintenance Mechanic
In prep for a trip I installed the Apex Autolynx disconnects. I chose to seal the snap rings from road salt and water using masking tape and gasket sealer, which seemed to work better than liquid electrical tape.

Assuming that these things last, they completely paid for themselves in that I was able to disconnect the sway bar and provide for my family a softer ride than otherwise. We were able to compare with and without disconnect and they're very happy to have the disconnect. This was their first time offroad and they were worried about all the bumps.

By the way, the stock Sport S shocks seemed fine. I did get some LT tires, though, which greatly reduced the side-to-side swaying, which was largely from the flex of the original street tires. On my first pickup I got whiplash from that after a few days.

And I had the LT tires at 55psi because they were getting pretty warm at 40psi while hauling our supplies and towing our trailer at 75mph. I didn't want to air down on the trails because we were not slipping and I was still carrying a cap and a lot of cargo even without the trailer. And airing back up to 55psi takes a while.

As for articulation and such, it did knock the suspension bump stops a few times when I was going faster than I should have on some largish rocks. But we never spun a tire.

To reconnect, I found it useful to place the palm of a hand on the ledge of the mounting bracket and get close enough to push almost straight down. Sometimes it didn't make a noticeable click on reconnect, but it worked each time.
Didn't happen to take pictures of how you sealed them?
 
OP
OP
bd100

bd100

Well-Known Member
Joined
May 31, 2022
Threads
28
Messages
764
Reaction score
746
Location
USA Midwest
Vehicle(s)
JT, WK2, ole' Ram
Nope. Just wrap masking tape around the disconnect on each side of each joint where the snap rings are, and seal with something, then remove the tape. You want to end up with sealer over each of the two rings, all the way around the diameter, for each disconnect. The joint where the nut screws in is already sealed by the thread locker, but you still want to do the other side of that nut where the snap ring is, plus the other end where the other snap ring is.
 

SloW8

Well-Known Member
Joined
Jun 17, 2020
Threads
20
Messages
270
Reaction score
544
Location
SLC
Vehicle(s)
Gladiator Mojave
Air down on the trails, it makes such a huge difference in comfort. Worth the extra 20 min to air up.
Sponsored

 
 







Top