What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS, NO GUN TALK]

[Sazabi19]

How do you like it? Did it help with the wondering steering wheel and does it pull to the right?

It does not pull to the right any and it has made the steering a bit more precise tight. It's still not quite performance car steering, obviously, but much better than the mushy factory unit. There is still a bit of play in the steering (dead zone) but this wasn't going to fix that. Only Jeep fixing steering boxes will do that.

@LoJac963 Any reputable wheel/tire outlet should have a selection of TPMS sensors when you buy wheels or tires. Depending on your state they won't sell you wheels without them. When you choose new wheels it's usually an option to add them to your order or even suggestion on the same/different page before checkout, just like lug nuts.

Sponsored

 

[Timdog]

Added atp grab handles to the front & back.. adding a bit more red into my JT

 

[LostWoods]

Got a chance to put some miles on my Fox stabilizer today and I highly recommend one. Like @Sazabi19, still has the typical small dead zone up top but it now feels much more weighted and precise.

I never had steering issues to begin with but this feels much more like tight, old school box instead of the over-assisted stuff most trucks come with today.

 

[uplandgunner]

I hear this repeated frequently, waiting on TPMS sensors. Why aren't the factory sensors swapped to new wheels? Where does one get new TMPS sensors and how are they added to the system to recognize them. Sorry, new to the Jeep world!

TPMS sensors have a specific frequency in regard to your vehicle. I wanted OEM ones that you just install in the wheel and the jeep will recognize. Leaving the others in the wheels coming off. Not cost effective to unmount and remount and balance the tires to swap them. Selling rims, wheels and sensors as a group brings a better cost recovery.

 

[TTEChris]

Not just today, but installed Road Armor fenders and rear bumper with a Warn VR EVO 10s. I also modified the factory Rubicon bed rails to work with the bumper.
I still need to wire the reverse lights and extend the power wires for the winch, but I really like how it turned out.

 

[Jdyowa]

Installed cai

 

[txn]

Finally upgraded to 285/70x17s with some rubicon take offs.

 

[NC_Overland]

How do you like it? Did it help with the wondering steering wheel and does it pull to the right?

Wondering steering sound awful.

 

[Climbhigh]

Installed the Diamondback HD cover this evening. Wife says I'm done speeding money on it for awhile

 

[Sazabi19]

Installed the Diamondback HD cover this evening. Wife says I'm done speeding money on it for awhile

You need to change your signature now

 

[Climbhigh]

You need to change your signature now

Done. Had to change some other things while I was in there

 

[LiftedLife]

Not just today, but installed Road Armor fenders and rear bumper with a Warn VR EVO 10s. I also modified the factory Rubicon bed rails to work with the bumper.
I still need to wire the reverse lights and extend the power wires for the winch, but I really like how it turned out.

Looks sick brother!

 

[sarcasm]

Used the 4"x8' bed management setup for the first time.

 

[Gatorized]

Installed GCPA GP-Grip grab hanldes. Not 100% compatible with my Sunshade/Sunrider setup but I was able to make it work.

Problem with the sunshade or Sunrider or both? What needed to be done to get around it? Haven’t installed my Sunrider yet and I have these handles too.

 

[msujedi]

You need to change your signature now

Done. Had to change some other things while I was in there

I believe that was a reference to your " Planned add-ons: , Rock Hard sliders, Rock Hard mid width winch bumper, Sunrider top, Mopar lift, 37x11.5 tires on 18" rims" in your signature below your posts.

And, I feel your pain. Things would go very badly for me if I spent more on mods.

Sponsored