Pic of AJT Key Fobs

[berb]

I have decided to replace my key fob with the AJT Key Fob. I am going to get a Blue fob, but I am still deciding between Red buttons and Screws or go with Black or go all Blue. I know a lot of people here have gone with AJT and I am asking for people to post pictures of their fobs here. If you go to the AJT website you can completely customize your fob through them.

https://www.ajtdesign-llc.com/

Sponsored

 

[berb]

The AJT aftermarket fob has been out for sometime now.. There are even, less expensive, Chinese knockoffs of it on amazon.com.

Yes, the AJT fob is real nice.... I have one.... but, I am now eagerly awaiting the new kid on the block so to speak.. It is a little different in a good way in comparison to the AJT offering.

I know, I for one will be buying one of these new offering aftermarket fobs in Jan. 2021 when they will hit the market.

Read here: https://www.jeepgladiatorforum.com/forum/threads/re-engineering-the-brick-keyfob.36077/

My AJT:

I saw that and they look nice. I might just wait until they come out and look at both. Thanks!

 

[TexasTJ]

I think the tan is a closer match to Toyota's quicksand than Gobi, but it works. It also fits in the little rectangle by the e-brake.

Rectangle at bottom left of picture.

 

[BAT]

I got one of the AJT didn't care for it waiting for something better to come along like mentioned in the forums.

 

[aureovin]

I posted this photo a while ago to show how you can make a tiny keyring using the inside of a wire nut ?

 

[JEEPER2287]

ok I hope I am not the only one that stared at this picture for a good 5 minutes thinking you had mounted the wire nut plastic onto your keyring too, But then finally realized it was a plastic ring around another key.

 

[JEEPmonkey]

ok I hope I am not the only one that stared at this picture for a good 5 minutes thinking you had mounted the wire nut plastic onto your keyring too, But then finally realized it was a plastic ring around another key.

SAME HERE, I didnt figure it out until your response, I can say I have the beta FOB linked above and it is amazing. I do not have experience with the AJT but the final product will be spot on from DI Labs

 

[Godfadr]

I went with black/red but swapped out the key door as well.

 

[Stitchedupseats]

I have the black with red buttons and red hardware. It looks almost pink. Buttons are super hard to press. Looks neat but not as functional as I would like. It has held up well though. It takes a beating in my pocket.

 

[Godfadr]

I have the black with red buttons and red hardware. It looks almost pink. Buttons are super hard to press. Looks neat but not as functional as I would like. It has held up well though. It takes a beating in my pocket.

Did you leave out the tiny little 'triangle' separators behind the buttons? I think they mentioned that in the instructions. I took mine out and didn't have a problem with the button push after that. Been using mine for about 15 months. I also have the soft buttons...they were much nicer.

 

[Empty Pockets]

Though I have a Sting Gray JT, I went with the tan AJT simply because I wear tan Levi’s 90% of the time. The buttons and screws are black. It is a big improvement over the factory fob, for sure. But I really want to see a phone or Apple Watch app to replace it. That, to me, is the ultimate solution.

 

[mazeppa]

I went with yellow for easy visibility.

 

[Boston Bill]

Though I have a Sting Gray JT, I went with the tan AJT simply because I wear tan Levi’s 90% of the time. The buttons and screws are black. It is a big improvement over the factory fob, for sure. But I really want to see a phone or Apple Watch app to replace it. That, to me, is the ultimate solution.

The Uconnect app does all the features that are in the key fob.

 

[TexasLEO]

I just paint matched mine to my Sarge green. It was a pain in the butt to get set up but I love my new fob. Bought my wife a white one to match her JL.

 

[antwon412]

Here’s mine. Tried to make it match the colors as best I could.

Sponsored