Mopar Dash Accessory Rail for mounting phones, ect

[GladyRoxor]

Part # 82219127AB
Anybody have this mount? The description is vague and pictures are limited. Is it a picatinny style rail? Which after market bases does it accept?

Sponsored

 

[SRFRAT67]

I would look at 67 designs products, similar but nicer IMO

https://www.67d.com/collections/gladiator

 

[kevman65]

I have this from Vector Off-Road, more versatility and mounting space.

https://vectoroffroad.com/products/jl-tube-dockbar

 

[Y-Guy]

@GladyRoxor I haven't found any installed customer photos yet, looked here and Wrangler forum. One guy on Reddit posted a photo from a dealership it appears.

 

[TestMule]

I would look at 67 designs products, similar but nicer IMO

https://www.67d.com/collections/gladiator

Totally agree. I have the 67 Designs bar and accessories in my Sport. Easy to install, well made, fit and finish is excellent, and it is versatile.

 

[Jteakus]

Where do the 67 design holders mount to the truck? I need something,
Anybody have a pic? Couldn't find any on website.
Edit: I found it

 

[Jammin jimmy]

The 67 Design that I have work very nicely.

 

[ShadowsPapa]

Part # 82219127AB
Anybody have this mount? The description is vague and pictures are limited. Is it a picatinny style rail? Which after market bases does it accept?

I'm looking at getting one but can't find the accessories for it. I like the fact it sits HIGHER. So many others sit right against the dash. I want some thing a bit higher. I have the bulletpoint phone mount now but again, it sits so the mount arm is so down low. I want some thing elevated like the MOPAR thing.

The 67 Design that I have work very nicely.

I assume they have one for the 24/25 models as yours won't fit my JT.

I may order the MOPAR setup just for kicks and see if I can find accessories for it.
I like that you can slide things left or right on it where my current mount is where it is, can't move, that's it.

 

[Jammin jimmy]

I also sometimes have a camera mounted on there just not right now. It mounts on an arm that I have going straight up. They have a lot of different accessories to make just about any angle or height you might need just by adding different accessories together. I’m sure not the cheapest but seem to work well.

 

[Jammin jimmy]

The 24+ mount is a bit different it mounts more on top of the dash instead of kind of down in it.

 

[Gvsukids]

I'm looking at getting one but can't find the accessories for it. I like the fact it sits HIGHER. So many others sit right against the dash. I want some thing a bit higher. I have the bulletpoint phone mount now but again, it sits so the mount arm is so down low. I want some thing elevated like the MOPAR thing.


I assume they have one for the 24/25 models as yours won't fit my JT.

I may order the MOPAR setup just for kicks and see if I can find accessories for it.
I like that you can slide things left or right on it where my current mount is where it is, can't move, that's it.

Bulletpoint has a track system for their mounts.

https://www.bulletpointmountingsolu...ngler-jl-jlu-gladiator-jt-platform-dash-mount

 

[GladyRoxor]

I went ahead and picked up the factory mount that I was asking about. It is a very solid mount and integrates perfectly with the dash. It has the old school Jeep Willys logo in the center. It fits a RAM Xmount that I had perfectly. There are two 1/4-20 tapped holes left and right. Mine has 1” balls and the base 1/4-20 stud mount. The rail itself is a picatinny style and should fit some of the Bulletpoint mounts and more.

 

[ShadowsPapa]

Bulletpoint has a track system for their mounts.

https://www.bulletpointmountingsolu...ngler-jl-jlu-gladiator-jt-platform-dash-mount

Fits up through 2023 only............

 

[ShadowsPapa]

I went ahead and picked up the factory mount that I was asking about. It is a very solid mount and integrates perfectly with the dash. It has the old school Jeep Willys logo in the center. It fits a RAM Xmount that I had perfectly. There are two 1/4-20 tapped holes left and right. Mine has 1” balls and the base 1/4-20 stud mount. The rail itself is a picatinny style and should fit some of the Bulletpoint mounts and more.

So this is what you got?

This is what I have now - I guess I'll have to find a ball to attach to that rail system so I can use my BulletPoint mount.

I think I'll call my dealer tomorrow.........

 

[GladyRoxor]

Yes that’s it. I’ll take a couple pics tomorrow. There is a channel cut out in the middle in addition to the holes I mentioned. I would say most 3rd party mounts would adapt to it.

Sponsored