What did you 3D print today?

[SightsOfIron]

Just some items for fun and to fine tune my skills.

Sponsored

 

[joseeph]

I already miss 3D printing. I own two printers, but unfortunately, both are currently out of order. The challenge arose as I purchased the printers while traveling, making it challenging to arrange for repairs when they malfunctioned.

 

[Wolf Island Diver]

Maxtrax Pin Wrench.

And……

A French Fries Holder:

 

[SightsOfIron]

Made 2 of these, the first was solid blue but the second one i tried out filament switch and it turned out well i think.

 

[Wolf Island Diver]

Knob wrench for my bed divider wall that’s detailed here:

https://www.jeepgladiatorforum.com/forum/threads/diy-slide-out-w-sink.74944/post-1305575

This allows you to get a lot more torque on these. I’m going to start posting the stls for these sorts of things on Thangs.com, etc. ….

This fits the following M8 knobs but probably others.

https://a.co/d/7giKiGO

I added magnets so I could store it somewhere convenient although these magnets are weak AF. In the center is a 13mm hex for additional light torque. 13mm is the common nut size for M8 bolts. Printed with 100 fill. It’s beefy.

 

[Wolf Island Diver]

This Tazer Holder.... Kinda of superfluous, kinda cool. The magnets I bought suck, so you have to use a number of them. It's also kind of cool because if you know where it will stick, you can just snap it up there. Now there needs to be one that clips to the gateway extension cable to keep that from flopping around. Maybe I'll remix this with a clip.

This is the one I made:
https://www.thingiverse.com/thing:5379255

 

[ErrngeElise]

The first black thing is a project for me. Just a crazy orientation that I am amazed worked.

the second black parts are a “widdle wadder” and some “widdle wecoverwy boards” that I’m going to mail to a friend for his 4Runner. He doesn’t know it so it will be a fun surprise


And the weird silver igloo looking thing is the last part for my neighbor’s senior design project. A real rush of a project and print. Just happy to finish the parts list for that. It was a lot

 

[mx5red]

The first black thing is a project for me. Just a crazy orientation that I am amazed worked.

the second black parts are a “widdle wadder” and some “widdle wecoverwy boards” that I’m going to mail to a friend for his 4Runner. He doesn’t know it so it will be a fun surprise


And the weird silver igloo looking thing is the last part for my neighbor’s senior design project. A real rush of a project and print. Just happy to finish the parts list for that. It was a lot

What is that, a trigger?

 

[ErrngeElise]

What is that, a trigger?

eh close. Nothing on this particular part moves. It's all solid and that thing is actually just a tab that fills a void, but good eye because this is part of a chassis for a 10/22. Think Enoch ODIN, but different design to be plastic and thus more affordable. The fcg goes in front of that tab and the grip behind it.

 

[SightsOfIron]

The first black thing is a project for me. Just a crazy orientation that I am amazed worked.

the second black parts are a “widdle wadder” and some “widdle wecoverwy boards” that I’m going to mail to a friend for his 4Runner. He doesn’t know it so it will be a fun surprise


And the weird silver igloo looking thing is the last part for my neighbor’s senior design project. A real rush of a project and print. Just happy to finish the parts list for that. It was a lot

i've seen that widdle wadder with magnets and can be "installed" to the vehicle before.

 

[SightsOfIron]

Any Helldivers here?

 

[ErrngeElise]

i've seen that widdle wadder with magnets and can be "installed" to the vehicle before.

Yup I bought about 100 neodymium magnets and a bunch have been glued on the backs of these pieces

 

[Wolf Island Diver]

Coming Soon (in 5-6 hours, when done printing): A new and improved 3-in-one Knob Wrench: aka "The Jeep Coochie"

1. Tightens various knobs like this one:

2. Tightens rack eyelets like these:

3. Turns MaxTrax Pins, both outer and inner+outer.

This works really well for opening and closing Maxtrax pins. I like this a lot better than the other Maxtrax wrenches I've printed and it's my own design. It's a lot deeper than the original knob wrench to accommodate the depth for the Maxtrax pins, but it fits in your hand better. This provides plenty of torque for all of its intended uses. It's plenty strong even printed as a draft. I'm not sure how the PLA will hold up under the heat of the tonneau cover. I may reprint in ASA if needed.

It has alignment markings on the back for the Maxtrax pin, eyelets and knobs, and on the front for aligning with the magnets when placing it on its mounting bracket. I'm going to resist the urge to print this in pink.

The mounting bracket has alignment pins to interface with a molle backing plate I made to fit my JCR bed molle panels.

When all this is done and tested, I'll post these somewhere and provide links.

 

[Wolf Island Diver]

Here it is…

​

 

[Wolf Island Diver]

FYI, The black on the tool is black filament. I’m printing all of this with a Bambu AMS unit, so I can print in up to 4 colors/filament types (up to 16 with multiple AMS units).

For example: This whale shark’s different colors are all filament.

Sponsored