What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS, NO GUN TALK]

[JCappy]

Same. And sketchers tend to be comfortable on my feet, of course I’ve only probably owned 2 pairs prior, and it’s been a while. I wore them all day and they were great.

I like that brand too. Most times my issue is width and sometimes have to get a wide shoe though not always. I need to look at them again tomorrow.

Sponsored

 

[WILDHOBO]

I like that brand too. Most times my issue is width and sometimes have to get a wide shoe though not always. I need to look at them again tomorrow.

For me with slip ons, it’s sometimes that one foot is taller than the other, so that foot feels tight. These are fine.

 

[JCappy]

For me with slip ons, it’s sometimes that one foot is taller than the other, so that foot feels tight. These are fine.

Good to know. Thanks

 

[drewcnit]

Started trying to figure out how to make a Genesis Dual Battery Kit that was located in the rear seat work with an American Adventure Labs rear seat delete.
At first thought I might fit it under it, but after talking to some friends decided to leave the underneath for storage and mount the battery kit on top of the seat delete in front of or to the side of my compressor.

Still trying to decide how I will move the wiring up through the 40% delete, may take a hole saw to it but need to get more of it in place to decide if so and where.
Back at it tomorrow, it got dark and I got hungry.

 

[Stan H]

Can someone please explain to me what does "ole uga uga" mean, if I had to guess is it some type of caveman language?

No no no that's not rights thats atleast a couple thousand years too advanced it's ooga ooga as the ancient chinese cryptic harbor freight hyrogliphs reveal

 

[WILDHOBO]

No no no that's not rights thats atleast a couple thousand years too advanced it's ooga ooga as the ancient chinese cryptic harbor freight hyrogliphs reveal

 

[MT1]

For the last 4 days give or take, been crawling around on the driveway installing a set of mint salvage Mojave axles from a 2024 model. Ever since I put 33" tires on my 2025 Base Sport JT, have been less than ideal for my like with the stock 3.73 gears. Even after adjust in JScan, got tired of the hunting and pecking between 7th and 8th gear on the highway and many times, it would hang in gear too long before shifting.

This axles set was sold by VIN as coming from a 2024 Rubicon X model but found out after delivery it was from a Mojave X and settled with the seller on a partial refund to accept them rather than deal with the hassle of a freight return. They were still minty regardless and losing out on a front locker was low on my priority list. Had the usual salvage pull shipping or removal damage of the front axle vent tube and steering bar drag link end being damage for which I repaired.

Came time for the install and found that having three floor jacks and set of modified moving dollies made this job a bit easier as it is unbalanced on the dive axle axis moving around. I was a one man band for this whole job and with the axles weighing in excess of 400+ pound each as shown, a lot of leverage use of the floor jacks and large pry bars to move stuff around was need. Also retained my FAD system and swapped the FAD delete plate on the replacement front axle for the FAD motor assembly.

Like anything, it is all nut and bolts but pulling the abs sensors to let hang with the brake caliper assembly made it easier. Floor jack under the pinion yoke area was also needed once the driveshaft was disconnect or the whole axle will violent shift again on the axis if not watching carefully. Rest of the install was just the reverse of removal.

Edit: Did have to drill out the front lower shock bushing to 9/16" that would accommodate the 12mm to 14mm mount bolt hole difference on the Mojave front axles.

I did have a couple of "While I am in here" things to accomplish. One was installing a Rusty's Offroad front trackbar reinforcement bracket. The second was installing the "Power Hop" damper on the rear axle.

Lastly, adjust the axle ratio settings in JScan for the new 4.10 gear ratio and took it for test drive. Did have some ABS issues that freaked me out but that was because the steering wheel was about 45 degrees out to the left but that was resolved once the steering position was adjusted in and straight. Have driven close to 75 miles today and everything seems fine and drives just like my two previous Rubicon JT's.

Well done!

 

[Verne]

I can tell you what I would LIKE TO DO to my Gladiator. I would like to swap out the lug nuts to black but can't land on what I want. Anyone have a suggestion?

 

[Freems]

Measured the truck yesterday... unless I get some rear squat out of these AEV HD springs when I get my tent installed I won't be fitting into the garage. I have exactly 10 inches of clearance right now, and the tent is listed at 10 inches high. Wasn't planning on getting a rear bumper, but I might have to now so I can clear the garage door lol

This is an easy fix…air down before you enter thr garage and air back when you roll back out of the garage.

 

[Stan H]

I can tell you what I would LIKE TO DO to my Gladiator. I would like to swap out the lug nuts to black but can't land on what I want. Anyone have a suggestion?

https://www.lowes.com/pd/Rust-Oleum...tin-Black-Spray-Paint-NET-WT-12-oz/5014869595
Sand em first stick a wire in em hang wires from a thin cord and go to spraying

 

[WILDHOBO]

I’ve been very happy with these. Good price and they have really held up to at least 10 removals and installs in several years.

https://www.extremeterrain.com/jeep...MImMa5kPf4jgMVI5zuAR2J1yNIEAQYASABEgKw7PD_BwE

 

[Verne]

https://www.lowes.com/pd/Rust-Oleum...tin-Black-Spray-Paint-NET-WT-12-oz/5014869595
Sand em first stick a wire in em hang wires from a thin cord and go to spraying

Thanks for the solution but that's a big hell no. I'll be spending cash for someone else to make a black set for me...

 

[WILDHOBO]

Thanks for the solution but that's a big hell no. I'll be spending cash for someone else to make a black set for me...

Check the link I shared in a previous post. The finish has held up great. Still black after tons of removals.

 

[Neomonk21]

I installed a set of Apex autoLynx swaybar quick disconnects today. Turned out great and it flexes well for an otherwise stock JTM.

 

[Verne]

Check the link I shared in a previous post. The finish has held up great. Still black after tons of removals.

Thanks...ordered.

Sponsored