What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS, NO GUN TALK]

[chorky]

Just workin away on a few more projects.

Sponsored

 

[MohaveVet29]

Installed some desertdoesit short seat jackets. Man night and day difference it made in comfort for driving. Only took about 20 minutes to do both sides and well worth the cost they are well made.

 

[toddarama]

Installed a Tazer JL Mini today. No pictures, because there isn't much to see and those pictures have been posted 1000 times already . Now I'm just waiting on the tire and wheel package and a Clayton Premium Offroad 2.5" lift with the Falcon SP2 3.3 shocks.

 

[Kyle10]

Washed it

 

[Verne]

Added these accent decals to the grill of the Mojave. From underground graphics.

 

[NeatFreq]

Finished my GMRS radio install. Zero holes drilled and no wires cut or tapped.

very clean install, nicely done

 

[Minty JL]

very clean install, nicely done

Thank you Sir.

For me its clean or nothing. Plus when I sell vehicles I want them free of hacked wiring and filled with holes......they always sell better and quick.

Though I have no intentions of selling I love this fucking thing.........it will be perfect with 4.88s and an LS Swap

 

[Minty JL]

Thought about taking off the Jeep emblems but I don’t mind those.
The badges look a little off, plan on adding some more beneath so they even out a bit

My thought process weight reduction LOL

......really, make it easier to keep the truck clean and one less place for mud and shit to collect

 

[RJinPV]

Looks good. Do you know what the distance is under it? I have an Engel cooler that is 18.5” . This topper is on my short list but this is my last thing I need to figure out.

I thought I'd try to answer your question since @LWBrew hasn't been seen since Nov 2022. I have a Bestop cover and it is 18.6 inches from the highest rib in the bed to the bottom of the cover's fabric. There is about 17 inches between the rear support rail and the next one further into the bed. Obviously, the support rails sit lower than the fabric. So your if your Engel cooler is 18.5 inches tall, and one of the horizontal dimensions is 17 inches or less, then it should fit.

 

[BringTheLightnin]

Installed some side decals on the Overland

Hey, I have the same wheels

 

[XJFanatic]

Hey all ?. Work has been keeping me busy but finally got a little break. Hope it’s going well on here!

Took the opportunity to install a hitch on the JLU as I need it for a bike rack with the wife reclaiming the JT. (Something about heated seats and steering wheel…) As well as gave them a bath, changed the JT’s oil and charged the TJ’s battery. All in a productive morning.

 

[legacy_etu]

I thought I'd try to answer your question since @LWBrew hasn't been seen since Nov 2022. I have a Bestop cover and it is 18.6 inches from the highest rib in the bed to the bottom of the cover's fabric. There is about 17 inches between the rear support rail and the next one further into the bed. Obviously, the support rails sit lower than the fabric. So your if your Engel cooler is 18.5 inches tall, and one of the horizontal dimensions is 17 inches or less, then it should fit.

Great, thanks for checking.

 

[Chuck]

Mine goes in tomorrow morning for rear passenger axle seal leak….

 

[3VOLVE]

Two day process to install my Next Venture Diesel Skids with UMHW. . Day 1 - remove stock skids, paint brackets, scrub and power wash under carriage. Day 2 - sand, prime, and paint any rusted areas and begin mounting skids. Biggest PIA part was removing the motor mount bolts.

 

[Jglad15]

Builtright utility rails, easy easy install and sturdy. Once the credit card statement closes I’ll be gettin some of there molle panels.

Sponsored