Jimmy07
Well-Known Member
- Thread starter
- #1
I figured I’d start a new writeup for the integrated trail camera system, so everything is in the first couple of posts, and I’ll edit these initial posts as needed if new/updated info comes along. I realize some of this is redundant, but it will all be in one spot instead of spread out through several pages.
To get the factory front trail camera and washer to work, it is an entire system that consists of: front trail cam, washer parts and pump, CVPM (central vision processing module), wiring, software to tell the BCM to use the system, and rear camera (no, you can not use your existing rear camera). The CVPM is the centerpiece of the system, and processes the camera images, sends them to the display, and sends the wash command. It needs a connector (which won’t be present) that supplies ignition power, ground, and wiring to the CAN IHS block to bring it online. It receives the front and rear camera inputs via coax cable, and sends the images to the display via coax cable. It’s location is on the back wall, behind the subwoofer (if equipped). Here’s a few images of it I grabbed from the other thread. Note the location of the CAN IHS junction block that the CVPM will connect to-
Here’s the list of all the OEM parts needed. If I missed any, let me know, and I will update the list as needed:
Front camera- 68436466AA
Front camera bracket- 68396626AB
(2) Camera bracket nut- 06510197AA
(2) camera bracket screw- 68090949AA
Camera grille section- 6QN24RXFAC
CVPM- 68329740AE
(2) CVPM bolts- 06104378AA
(2) CVPM snap nut- 06506955AA
Camera washer hose- 68370828AA
Camera washer nozzle- 68370210AA
Washer nozzle elbow- 68370825AA
Washer Pump- 68310928AA
There is a different part number for the washer pump jumper harness, but I don’t think it’s necessary since the wiring is the same except for one different colored wire. @bryanklay will confirm, and I’ll update this.
Rear camera:
Gator- 6NN98VGVAD
White- 6NN98GW7AD
Granite Chrystal- 6NN98LAUAD
Gobi- 6NN98RUAAD
Red- 6NN98MRCAD
Sting gray- 6NN98PDNAD
Black- 6NN98DX8AD
Billet silver- 6NN98JSCAD
Hydro blue- 6NN98MBJAD
Punkn- 6NN98SE4AD
To get the factory front trail camera and washer to work, it is an entire system that consists of: front trail cam, washer parts and pump, CVPM (central vision processing module), wiring, software to tell the BCM to use the system, and rear camera (no, you can not use your existing rear camera). The CVPM is the centerpiece of the system, and processes the camera images, sends them to the display, and sends the wash command. It needs a connector (which won’t be present) that supplies ignition power, ground, and wiring to the CAN IHS block to bring it online. It receives the front and rear camera inputs via coax cable, and sends the images to the display via coax cable. It’s location is on the back wall, behind the subwoofer (if equipped). Here’s a few images of it I grabbed from the other thread. Note the location of the CAN IHS junction block that the CVPM will connect to-
Here’s the list of all the OEM parts needed. If I missed any, let me know, and I will update the list as needed:
Front camera- 68436466AA
Front camera bracket- 68396626AB
(2) Camera bracket nut- 06510197AA
(2) camera bracket screw- 68090949AA
Camera grille section- 6QN24RXFAC
CVPM- 68329740AE
(2) CVPM bolts- 06104378AA
(2) CVPM snap nut- 06506955AA
Camera washer hose- 68370828AA
Camera washer nozzle- 68370210AA
Washer nozzle elbow- 68370825AA
Washer Pump- 68310928AA
There is a different part number for the washer pump jumper harness, but I don’t think it’s necessary since the wiring is the same except for one different colored wire. @bryanklay will confirm, and I’ll update this.
Rear camera:
Gator- 6NN98VGVAD
White- 6NN98GW7AD
Granite Chrystal- 6NN98LAUAD
Gobi- 6NN98RUAAD
Red- 6NN98MRCAD
Sting gray- 6NN98PDNAD
Black- 6NN98DX8AD
Billet silver- 6NN98JSCAD
Hydro blue- 6NN98MBJAD
Punkn- 6NN98SE4AD
Sponsored
Last edited by a moderator: