Rack compatible with bak revolver x4s

[wawatusi]

Hi,

New gladiator owner here, I just installed the back x4s and would like to add a simple cross bar rack to the t-slots, is this what I would need or are there better ones out there?

thanks!

https://a.co/d/iL1xcYH

Sponsored

 

[skiline900]

I have the Yakima OverHaul HD bed rack, you will need the T-Slot adapters.

 

[Ferd]

This is an Amazon rack. Any regular flat base, t-slot rack should work. Like the other said, Yakima will need an adapter.

 

[Riding with Gladys]

Xtrusion overland also makes a great rack that works well. I run the same set up

 

[wawatusi]

Thanks

 

[stuckinohioJ5]

anyone have the Yakima Outpost w the bak revolver 4S? Would like to see images and also understand if there is enough clearance for the cover?

 

[stuckinohioJ5]

I have the Yakima OverHaul HD bed rack, you will need the T-Slot adapters.

any chance you could share a couple images or the install? is there any interference w the seal on the cover?

 

[Ferd]

I spoke to the Real Truck rep and even with the adapter, there is little to no clearance to roll the cover back without wearing out the seal.

 

[stuckinohioJ5]

thanks, that's what I was concerned about. I like the lower profile so may add a piece of aluminum extrusion to lift it up. still a work in progress...

 

[skiline900]

any chance you could share a couple images or the install? is there any interference w the seal on the cover?

Not my post, but I did the same as seen here: https://www.jeepgladiatorforum.com/...tonneau-install-and-review.33134/post-1307947

 

[RealTruck]

Hi,

New gladiator owner here, I just installed the back x4s and would like to add a simple cross bar rack to the t-slots, is this what I would need or are there better ones out there?

thanks!

https://a.co/d/iL1xcYH

The Elevate Rack is the most popular addition to the X4s. It fits seamlessly into the integrated T-slot rails without any modifications. The telescoping design of the rack allows you to set the height at 18", 23" or 28".

 

[Exceed Fabrication]

Welcome to JGF! Our new SR1 bed rack is perfectly compatible with X4s!

A simple low profile rack featuring our iconic removable logo!

https://exceedfab.com/products/sr1-sport-bed-rack

https://www.jeepgladiatorforum.com/forum/threads/sr1-bed-rack-by-exceed-fabrication.89452/

 

[stuckinohioJ5]

Not my post, but I did the same as seen here: https://www.jeepgladiatorforum.com/...tonneau-install-and-review.33134/post-1307947

thanks!

 

[wawatusi]

The Elevate Rack is the most popular addition to the X4s. It fits seamlessly into the integrated T-slot rails without any modifications. The telescoping design of the rack allows you to set the height at 18", 23" or 28".

thanks i ended up with a rhino rack setup which is exactly what i needed. The cover though the weatherstripping at the front wont stick, any ideas?

it has a rhino liner, and i cleaned and even pressed the weather stripping in. just curious if you have any solutions.

 

[RealTruck]

thanks i ended up with a rhino rack setup which is exactly what i needed. The cover though the weatherstripping at the front wont stick, any ideas?

it has a rhino liner, and i cleaned and even pressed the weather stripping in. just curious if you have any solutions.

Awesome, I'd love to see your setup once you have everything installed!

For the bulkhead seal, you can use a 3M adhesive promoter to get the seal to stick to the Rhino liner. Make sure you've cleaned the area with a lint free cloth and rubbing alcohol first.

Sponsored