Sponsored

whysoserious

Well-Known Member
First Name
Joe
Joined
Mar 20, 2023
Threads
14
Messages
558
Reaction score
943
Location
Central Texas
Vehicle(s)
2021 JT Mojave, 2006 Rubicon
Occupation
Professional former employee
Thought I'd throw out a few pictures of my updated setup. The last trip in July was great beta run on the new RTT and awning. I had two Yeti loadout boxes in the bed for the bulk of my supplies, along with a couple water jugs and an ice chest. This was a pain in the butt due to my RTT setup being so close to the top of the bed rails. It's a 6" Billie Bar rack that keeps my RTT low enough that I can park my JT in the garage where I have a lift to raise it up the the ceiling and out of the way when not in use. And my garage is the only place to store my RTT.

I looked for quite some time on the Interweb for a solution to accessing my entire bed area. With the old setup, there was over a foot of space at the front of the bed that I could not get to, for any practical purposes. So, my hunt was for a full bed slide (or as close as I could get) that was as low as possible to maximize the height under my bed cover; I wanted to keep the bed cover while overlanding. I ran across OzTech and their Skeletal System Slide (https://oz-tech.com/products/skeletal-system-utility-slide-modular-slide-sytem). Had many back and forth emails with Hunt Nosari asking a multitude of questions. He was very prompt in all his responses. I finally pulled the trigger at the beginning of October. I also ordered several of the mounting plates that fit the Milwaukee Packouts.

While I feel very certain I've got more building to do on my JT, it's pretty well ready for the next trip and more testing of equipment to see what need to be changed. I still have the homemade full rear seat delete that cost me about $100 will all the hardware and such. It holds my tools and recovery gear, as well as my power station and my Iceco fridge.

Any, yes, the slides were not cheap, but they are manufactured in the US and are very well made. And if I didn't mention it before, I'm not getting rid of this Jeep any time soon.

Jeep Gladiator My Overlanding setup IMG_20261120_120403137_HDR
Jeep Gladiator My Overlanding setup IMG_20261120_120408598_HDR
Jeep Gladiator My Overlanding setup IMG_20261120_120422019_HDR
Jeep Gladiator My Overlanding setup IMG_20261120_120354730_HDR
Jeep Gladiator My Overlanding setup IMG_20261120_120435444_HDR
Sponsored

 

Alpine Warthog

Well-Known Member
First Name
Eric
Joined
Nov 15, 2022
Threads
80
Messages
1,184
Reaction score
1,462
Location
Allegheny National Forest, PA
Website
www.instagram.com
Vehicle(s)
21 Gladiator, 98 XJ
Occupation
Retired USAF Police Officer
Vehicle Showcase
1
I like it. I'm building an expedition trailer to overland with. I've been trying to figure out storage too. I opted for a decked drawer in the bed for vehicle specific recovery and trail stuff. All "camping" specific stuff goes in the trailer. I try to walk the fence on being an offroader and an overlander. I think the trailer will by my answer.
 

Metalhead

Well-Known Member
First Name
Preston
Joined
Mar 29, 2025
Threads
42
Messages
209
Reaction score
258
Location
Southampton Pa
Vehicle(s)
2024 Jeep Gladiator Sport S
Occupation
Emergency Vehicle Technician
Nice setup. I also have the 6 inch billie bars with an ikamper tent mounted on it plus a tonneau cover. Been thinking about adding the awning mounts from billie bars. Did you have to shift the tent more to one side for the awning mounting brackets so it wouldn't interfere with opening the tent? I was looking at slides for the bed also and man it was expensive for a decent setup.
 
OP
OP
whysoserious

whysoserious

Well-Known Member
First Name
Joe
Joined
Mar 20, 2023
Threads
14
Messages
558
Reaction score
943
Location
Central Texas
Vehicle(s)
2021 JT Mojave, 2006 Rubicon
Occupation
Professional former employee
Nice setup. I also have the 6 inch billie bars with an ikamper tent mounted on it plus a tonneau cover. Been thinking about adding the awning mounts from billie bars. Did you have to shift the tent more to one side for the awning mounting brackets so it wouldn't interfere with opening the tent? I was looking at slides for the bed also and man it was expensive for a decent setup.
I did shift it completely to the driver side to be even with the cab profile. It just clears my awning mounts on the passenger side. I use the aluminum extrusions as my awning mount:

Jeep Gladiator My Overlanding setup IMG_20261120_150843486_HDR
 

Bandit’s Lair

Well-Known Member
First Name
Jason
Joined
Jul 9, 2025
Threads
54
Messages
4,890
Reaction score
8,398
Location
Southern California
Vehicle(s)
2021 Gladiator Sport S
Occupation
Retired
Very impressive. How far above the bed do the drawers sit and what is the weight rating on them? Wondering if that could be a solution for a spare carrier in the upright position to make room usable between the spare and tailgate. If I can pull the drawer out to access spare I could wiggle it around stuff and make it work a little better.
 
OP
OP
whysoserious

whysoserious

Well-Known Member
First Name
Joe
Joined
Mar 20, 2023
Threads
14
Messages
558
Reaction score
943
Location
Central Texas
Vehicle(s)
2021 JT Mojave, 2006 Rubicon
Occupation
Professional former employee
Very impressive. How far above the bed do the drawers sit and what is the weight rating on them? Wondering if that could be a solution for a spare carrier in the upright position to make room usable between the spare and tailgate. If I can pull the drawer out to access spare I could wiggle it around stuff and make it work a little better.
The weight rating is 500 pounds per slide, evenly distributed. The "load" surface, where you would mount "stuff" in the drawers is 2.15" above the bed ribs.
Sponsored

 
 







Top