What do u have coming in the mail?

[antwon412]

Mojave it’s currently at the shop getting new gears and a front locker put in. So today I ordered the manifold kit needed for the air compressor. I mounted a while ago in order to run my front locker.

Sponsored

 

[813 Fabrication & Design]

Wish they had a way to use the bottom part of the wall, the part that covers the back panel. I think it’s a clean look, but they said there is no way to connect it unless you but the whole back wall. I don’t want to cover my back window though.

AH, yea, the current center section would require all three parts I believe. I am sure he could design a wall section to work, but it could be a while to get something like that going I believe. I was talking with someone at Overland Expo East about the back wall and may have an idea that I am going to explore

 

[Toyfrog]

AH, yea, the current center section would require all three parts I believe. I am sure he could design a wall section to work, but it could be a while to get something like that going I believe. I was talking with someone at Overland Expo East about the back wall and may have an idea that I am going to explore

I emailed them a few times and they even asked what I would interested in using it for. I told them an option to hang gear and mount some quick fist would be a nice option. If they would sell me just the back piece without the top, I’m sure I could find a way to mount it, maybe make it hinge and lock to the original seat back tabs. One of your bed molle panels would be a nice option for the mounting solution for gear and “broom” sticks. ?

 

[WILDHOBO]

Replacement third brake light and replacement fender Jeep badges from @AllMoparParts.com. Badging was installed super crooked from the factory, and it finally made me nuts enough. Third brake light has a bad connection at the light. I ordered a replacement light and harness so I not need to take it apart one more time.

 

[GEETCH]

Wish they had a way to use the bottom part of the wall, the part that covers the back panel. I think it’s a clean look, but they said there is no way to connect it unless you but the whole back wall. I don’t want to cover my back window though.

I felt the same way, would be awesome to just have the lower half.

 

[Sarge502]

2024 grille (eventually since its a preorder)
Warn Medium Duty Recovery Kit

 

[Toyfrog]

I felt the same way, would be awesome to just have the lower half.

I guess they assume that everyone wants to cover up their back window when doing a seat delete? I’m sure there is a way to attach the back wall portion to the seat delete without having the piece covering the back window?

 

[GEETCH]

I guess they assume that everyone wants to cover up their back window when doing a seat delete? I’m sure there is a way to attach the back wall portion to the seat delete without having the piece covering the back window?

Probably, need to make a custom bracket I recon

 

[TestMule]

I several things coming in the mail this week!

1. Two Midland GMRS handheld radios. The two I purchased previously perished prematurely.

2. A Fishbone Offroad Hi-Lift jack mount kit that will bolt to my Rebel Offroad bed rack.

3. A 4-pack of Teraflex bed rail tie-downs.

I should be up to my eyeballs in packages by Thursday afternoon.

 

[Lunentucker]

https://www.amazon.com/2-Finger-Compatible-Gladiator-Cherokee-Printed/dp/B09DDDNQGC/

 

[Rick_Jame55]

AMSOIL Products for diffs and transfer case
-Folding camping table for this weekend outing that will be above 9,500 feet in Pike national forest.

 

[WILDHOBO]

They’ve all arrived over the last week or so. Replacing front factory bump stops, which I’ve completely destroyed. I’m using fox hydraulics for the top, and synergy stackable pucks on bottom to be able to adjust bump without removing a bolt. At the same time, I’m installing teraflex 1/2” spring spacers on all four corners, to get to 3.5 in the front and 5” in the rear. I’m currently at 3” and 4.5”, give or take who knows how much. Unrelated to that project, received an extra teraflex nomad wheel as an in box spare, since they’ve been discontinued and I love them.

 

[Zachanadandy]

AEV 2" lift coming for my new 2023 mojave. Unfortunately it won't be here in time for our desert trip next week.

 

[Doofus]

waiting on JKS J-Kontrol 3-3.5 coil spring lift with fox 2.5s and a reaper off-road stubby bumper! I can't wait

 

[Saltymedic]

No annoying logo's and much more cheap @ $30

Sponsored