What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS]

[DirtyD]

Finally done it:
1.5" Daystar leveling kit
315x70R17 Milestar Patagonia
17x9 -12 Dirty Life wheels.

Saw your post in HJS, looks great! Planning on letting Tom regear and possibly lift mine this summer!

Sponsored

 

[Bbannongmu]

finished up ACE JT Expedition Bumper Install and video

 

[HTXGladiator]

Saw your post in HJS, looks great! Planning on letting Tom regear and possibly lift mine this summer!

Tom is good man....in between being jam packed with work, he's working on getting all his fabrication equipment set back up. I'm planning on ordering coilovers and letting him build my suspension.

 

[Kitfoxbill]

Diode Dynamics Halo installed. Rubicon non led headlights. Full installation in lights.

 

[TheSolarWizard]

Received and installed my Bak x4 Revolver tonneau! Absolutely love the fit and finish, and looking forward to getting my rhino rack on the accessory rails.

more pics please!

 

[TheSolarWizard]

Smartliner got it, put it down, fits Great, like it, Recommended.

would this interfere with molle panels?

 

[cbl1]

Mounted Rotopax on the factory trail rail.

I used the Rotopax Toyota/Nissan adapter - https://rotopax.com/toyota-nissan-truck-plate.html

I'm using the deluxe Rotopax Mount mounted vertical to the plate.

Absolutely perfect fit - and very secure.

Only issue was the bolt that came with it was overly long. I picked up a correct sized bolt (which also was better as it was matching black) at Lowe's …. 5/16-18 x 1 Cap Screw (in the drawer section)

The Rotopax is the 2 gallon which fits perfectly. Will not interfere at all with my Tonneau Cover as well below the top edge of the bed - fairly flush with top of the rail.

 

[Blknblu]

added a Fox front stabilizer shock to compliment my Mopar 2 inch lift. took 10 minutes.

Bruce

 

[Jeepnoob34]

These are going on today! Taking a stab at the new(ish) Kenda’s Klevers 35x10.5r17. So far all I have read they have had great reviews! Time will tell.

You better not let that Frenchie fall off that tire. Probably cost as much as 8 of those tires lmao.

 

[JTzntz]

Smartliner got it, put it down, fits Great, like it, Recommended.

Buzzlb, I also have a few question about your SmartLiner: What is it made of? It it hard or is it a soft foam? Based on pics it's hard to tell. Wondering if it would hold up to the abuse a drop in or spay in liner would? Thanks!

 

[Pizziola29]

I did not use the cross over in the box with the Kenwood's, I think the stock system is already filtered for the dash speakers. I used the adapters Crutchfield sent and plugged right in. Turned it on and was very pleased

Hey Dave, which adapters ? Can you share a picture or model number? Crutchfield is out of stock so I bought on ebay. Need to see what I need to buy additionally.

 

[DAVECS1]

Hey Dave, which adapters ? Can you share a picture or model number? Crutchfield is out of stock so I bought on ebay. Need to see what I need to buy additionally.

 

[Pizziola29]

Just ordered! Thanks very much!

 

[mcolbyb]

I threw a set of Rubicon front shocks on my Sport S. I have the rears ready to install as well, but will take care of those this coming weekend. The difference in ride quality is pretty nice just from swapping out the front, and I couldn't beat the deal I got from an ebay seller ($206 for all four shipped).

nicely done.

I’ve been planning this for a while, finally got around to adding my 12v power accessory ports to the bed. I ran marine 8awg wire from the battery inside the frame rails to the rear, added a fuse block at the rear frame, then came up with a switch powering a usb C, 3 usb A, and a cigarette lighter port. Then I also have an always hot SAE plug. My Jeep came with the factory inverter so I already have 110 in the bed also.

I'm working on the same thing. How did you adhere your fuse box to the frame? Did you find a gromet for where the battery cables go into the frame?

 

[Jdyowa]

Installed the Fab Four Overland rack on my Overland. This thing is BUILT!

Sponsored