What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS, NO GUN TALK]

[OldFloridaMan]

Nothing major, just added a couple graphics.

I posted in another thread that the Gladiator is named Feegle (after the Feegles from Terry Pratchett's books). So I'm going to have a line of Feegles running across the bottom of the back window...

Sponsored

 

[punk'n]

What are the details on the box? Where did you get it?

Its a Kolpin Black Rear Trail box- # 93201. I was searching for something that would fit under the tonneau I ordered, be lockable and weatherproof. I liked the size too (37 x 17 x 13.625 tall).

They are available at a bunch of places. Summit racing even has them :
https://www.summitracing.com/parts/kpi-93201

 

[Troybilt]

I ordered a set of Ace Engineering rock sliders. Going to pick them up at Ace as soon as they are ready. Hope I get them before my trail trip September 20th.

 

[Markpod7]

Smoked out the side markers...havent decided if ill keep it or not what do you guys think?

 

[Troybilt]

Smoked out the side markers...havent decided if ill keep it or not what do you guys think?

Not a fan. But if you like it I'll get over it

I do like the front plate. Wheres your air dam?

 

[Proximo]

I ordered a set of Ace Engineering rock sliders. Going to pick them up at Ace as soon as they are ready. Hope I get them before my trail trip September 20th.

Where ya going Troy?

 

[Troybilt]

Where ya going Troy?

Going to Arkansa to pick up a cat

https://www.jeepgladiatorforum.com/forum/threads/going-to-chase-some-more-badges.33871/

 

[SloW8]

Made a contraption to hold the roof in the little bump out corner of my garage.

I built a shelf out of a 1x4 and mounted it a few inches away from the wall. I made it with two pins that stick up through the board to catch the middle two bolt holes in the back edge of the roof and also wrapped it in padding. Then added a ratchet strap to hold the front up. I would have liked the strap to be a little further forward but the joists were not cooperating.

 

[dustanner]

Installed my BuiltRight rail and Waterport Shower.

my BuiltRight arrives tomorrow for this exact purpose. Love the Waterport! But from the looks of this, I should have chose passenger instead of driver. Care to share details on how it’s mounted? Thanks!

 

[Fawkes]

Put a vinyl wrap on the tailgate and around the tail lights and then took it out naked!

How much for the wrap if you don't mind me asking

 

[DougM55]

Hopefully it shows up soon. Mine came 2 days after ordering it. I was shocked!

If you have a plastic stock bumper with parking assist you’ll need to buy different bezels and/or brackets. I’m still working on that. It looks like the part number listed in the directions is wrong.

I can confirm the sensor bracket part number as 68335621AC. You’ll need 4. Cost me a total of $11 at my local dealership. Looks like these brackets are originally for a Ram 1500.

When installing, the widest opening on the back of the bracket faces up on all 4. Then the sensors snap into the brackets from the back with the plug facing up. Turned out nice!

 

[Deleted member 30519]

I can confirm the sensor bracket part number as 68335621AC. You’ll need 4. Cost me a total of $11 at my local dealership. Looks like these brackets are originally for a Ram 1500.

When installing, the widest opening on the back of the bracket faces up on all 4. Then the sensors snap into the brackets from the back with the plug facing up. Turned out nice!

So mine will have the open holes exposed when installed since I don't have sensors? I don't think I do at least. All I have is a sport with basic back up camera.

 

[Fawkes]

https://www.ebay.com/itm/Fits-2020-Up-Jeep-Gladiator-JT-Tailgate-Blackout-Vinyl-Graphics/254612269699?_trkparms=aid=1110001&algo=SPLICE.SIM&ao=1&asc=20191002094254&meid=e8c0c15680fe409491ea7ab4bb67666b&pid=100891&rk=2&rkt=6&sd=383366955825&itm=254612269699&pmt=0&noa=1&pg=2332490&_trksid=p2332490.c100891.m5206

Other places do it as well. Be careful about the custom text— if it’s cut out to show body color, there are a couple holes under the “Jeep” logo that may get exposed. If you’re going to overlay letter, no need to worry. If you just want the tailgate black (and not the tail light parts), https://yellowbeedesigns.com/ sells them much cheaper.

The one on Ebay doesn't look like it covers the same amount of area. Is that the one you ordered?

 

[DougM55]

So mine will have the open holes exposed when installed since I don't have sensors? I don't think I do at least. All I have is a sport with basic back up camera.

They provide 4 black textured circles that cover the holes.

 

[Cwelroy]

The one on Ebay doesn't look like it covers the same amount of area. Is that the one you ordered?

I ordered mine from here: https://yellowbeedesigns.com/produc...020-10x49-inches?_pos=24&_sid=7d7f10e4c&_ss=r But as part of the order I asked for a custom size, 6”x49”. 53” covers the full tailgate width.

Sponsored