What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS, NO GUN TALK]

[ArmyMP]

Called to check on my service status. No parts truck today due to weather.

Sponsored

 

[jeepmeepmeep]

Preparing for the tent arriving tomorrow. Voodoo Max Mod rack.

Is that the 10”? Will a soft roll up cover be able to roll up under that?

 

[injaneer]

Is that the 10”? Will a soft roll up cover be able to roll up under that?

Thats what she said.

 

[Gren71]

Called to check on my service status. No parts truck today due to weather.

funny, im in the same boat.

 

[ecidiego]

Why would you delete the freedom panel storage bag?

 

[Chuck-a-Palooza]

So lets See it!!

Without phone or camera:

I have since experimented with switching these around. My phone really sticks up high due to where the power button is in relation to the holder.

 

[BLK HOLE]

Is that the 10”? Will a soft roll up cover be able to roll up under that?

Yes and yes.

 

[JTzntz]

I have since experimented with switching these around. My phone really sticks up high due to where the power button is in relation to the holder.

Yeah, hated how the devices were high and blocked some of the windshield. Ended up getting short (67 designs Nano) arms to move them down.

dropped Both my phone and iPad mounts down. Much better for me.

 

[NonHyphenated American]

Concluded my bumper and winch saga. The red tow hooks were only used to align the plate before tightening. Rugged Ridge mounting plate, Rugged Ridge Trekker 12.5k winch with synthetic line and Factor 55 flat link. Despite the instructions for the mounting plate I did not have to elongate the bolt holes on the skid plate mounting brackets. Just had to loosely install the bolts and manipulate the skid. The winch power is disconnected by a 500amp isolator that gets turned on by the Voswitch. Before winch and bumper I was at 35" at the center of the fender. Current combo dropped it to 34.5". The rear sits at 37". Looks like I will be getting Rubicon front springs and a 1.5" leveling kit.

I originally ordered a Rustys winch plate but it was .5" too long where it mounts in between the frame rails. I have been in contact with Rustys customer service and hoping for a resolution on getting my money back.

 

[Brekka]

Finally got around to fabbing up a quick bracket for the 1.3 Gal gas can, originally for a motorcycle so had to modify a little bit. It's the largest can I can get in the space with the MOLLE panels and Bedslide in there.

Was a little skeptical at first but it's been kicking around the the bed for months and hasn't leaked at all.

How do you like the bed slide? That setup is awesome!

 

[Just Mark]

Yeah, hated how the devices were high and blocked some of the windshield. Ended up getting short (67 designs Nano) arms to move them down.

dropped Both my phone and iPad mounts down. Much better for me.

I'm so doing this!

 

[JTzntz]

in hindsight, I probably would’ve gone with the Offroam vent mount bases to not have so many arms and connectors all over the place. Though I haven’t experienced them first hand, it seems they would be as sturdy as the 67d mounts/arms and also can be fitted with 20mm mounting balls for mixing and matching (I prefer the 67d 20mm over the RAM stuff)

already have a bunch into the 67d setup, so sticking with it for now. Here’s what it looks like from the drivers seat:

 

[Roklimo]

Nothing really. Ordered ordered 37’s and new wheels, and a Tazer lite. The “do to it” part comes next week.

 

[Gene26]

Ordered some parts for the dadiator. Metalcloak 3.5 dual rate lift, the last set of Falcon 3.1 shocks in the country for my lift and a set 37 inch nitto terra grapplers!!!!! FedEx guy is going to hate me

All parts have arrived should be installing all Monday.

 

[DrJ]

Washed and waxed a few if my toys including my gladiator. Took a high speed buffer to my Avalon and Tacoma before a second wash and then wax. Not too bad for a 5 year old taco. But, man it's a lot of work. First world problems right!

View attachment 216218

View attachment 216219

What box is that on your JCR 1/2 rack?

Sponsored