What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS, NO GUN TALK]

[XraytecH]

After seeing some of the other members change their cabin filters, I thought I would change mine. I didn't realize it was so dirty. I replaced mine with a Mopar one, but it appears there are several cheaper options, including Wix.

How many miles on yours?

Sponsored

 

[Jeepmonster]

How many miles on yours?

About 12,600 miles. I live in a relatively benign region- not much dust, pollen, or humidity. I looked closely at the pleats (dirty filter), and at closeup, it does look like some of the charcoal is visible. I might pull the new one out periodically and compare. Maybe it's not as bad as it looks.

 

[GEETCH]

How did the mount attach to the inside of the cab ? Thanks

It has dryer clamps that I put around the roll bar same as the extinguisher itself.

 

[Gren71]

Was it hard to take out/replace ? Guessing its located under the glove box ? I have very low miles and could check what my oem filter looks like for comparison.

SUPER easy. Took a couple minutes to do.



im assuming the diesels are the same interior guts as the 3.6 is.

 

[mrworldwide79]

It's a fairly straight forward and easy project. The most time-consuming parts were replacing the trim that held the 115V Power button to the left of the steering column and removing the cover in the bed (disregard if you don't have bedliner).

If you watch this YouTube video in full it will save you a ton of time -
(if you're on this forum many many thanks).

I chose not to disconnect/open up the door because I have some short column tools that could unscrew some of the bolts.

Did you remove all of the dash Panels like the guy in the YouTube video did?

 

[shockingtruth22]

Yeah, I removed everything as shown in the video. The long piece that goes over the width of the front is intimidating but once you get started it comes right off. Just make sure you keep the metal retainers on the trim piece and not the vehicle. I had the majority of the center console apart a few times before for a dashcam install so it was fairly easy.

Did you remove all of the dash Panels like the guy in the YouTube video did?

 

[Orange01z28]

So, I’ve been waiting a while to talk about my new vinyl I wanted to do. I wanted to add something to the rear without removing the Jeep logo, and with the help of @pixeldecals we came up with a plan. I wrapped the tail light and only part of the tailgate. I think it looks good, and I actually didn’t screw it up. Let me know what you think!

The AZ flag on the front looks cool

 

[Gator Pit]

Bestop sunrider for hardtop... now come on warm weather!

 

[HemiMagnum1]

Do you have a link for those black out fender markers?

You can customize on www.pixeldecals.com ...I went with antique bronze outline and matte black body.

 

[Markpod7]

You can customize on www.pixeldecals.com ...I went with antique bronze outline and matte black body.

I mean the lights

 

[UGAEngineer]

Footwell lighting

Nice! I did that too. Didnt use the color changing leds though because I wired it into my dimmer switch.

 

[IslandFalconer]

where did you pick up the USB-C port ? Did it come with the bracket that's filling up the rest of the slot ? I have the same BulletPoint setup. A universal phone holder on each side and a GoPro mount in the center. I got the 10cm arm for the drivers side so it would be a little closer to me , ended up with the gray/black carbon fiber because I wasn't sure how it would match up... but looking at yours, it looks great !

I made the plate and the usb-c cable is a panel mount type from Amazon. The plate is held on by the two ball mount bolts. And two screws to hold the cable to the mount.

https://www.amazon.ca/dp/B086W696KM/ref=cm_sw_r_cp_api_i_71MG748RPM39JAGDK74K?_encoding=UTF8&psc=1

 

[polarisTXguy]

Quickly running out of time before we head to UT on Saturday for 17 days. So I am frantically trying to finish up projects.

I can’t stand wires everywhere in any vehicle. So I purchased a Media USB / Mini C plug off of EBay ($30) and modified it and the dash to work with my Bullet Proof mount. I think it turned out great and works as designed. Even made a custom radar mount with hidden power. This is not just a charging port but ties into the factory audio with all the CarPlay functionality


Low cost mod that I think is cool.

 

[rafaelsmith]

Readylift - 2.5" sst lift kit installed.

 

[cdyoung9799]

Readylift - 2.5" sst lift kit installed.

Great color. One of my favorites.

Sponsored