What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS, NO GUN TALK]

[AblePotato]

Added grab handles and side steps to my Rubicon.

Hang on...is that pizza seat belted in?

Sponsored

 

[NC_Overland]

Needed to tone down the chrome.

 

[eligius]

Hang on...is that pizza seat belted in?

It's the best pizza in town from DaVinci Pizzaria, didn't want to drop it, lol.

 

[LiftedLife]

Looks very sharp.... where'd you get the stripe/graphic set?

I had a local graphic guy cut and install them while we installed mopar lift, wheels and tires. It’s also on the center of the hood. Charged me $160 installed.

I will send a better pic of the hood but I had this one. Doesn’t show much. Just had changed headlights and changing bumper.

 

[Moab]

Needed to tone down the chrome.

I like this graphic technique. How was this done? Did you purchase a kit/decal set.
Make your own?
I’d like to treat mine to this.

 

[NC_Overland]

I like this graphic technique. How was this done? Did you purchase a kit/decal set.
Make your own?
I’d like to treat mine to this.

Just a set I ordered on amazon. Two sets. One for the sides and one for the tailgate. They just stick on top after some alcohol and careful placement. Didn’t take long at all.

 

[sgtkersh]

Super quick install. No more freedom panels! Bestop Sunrider for Hardtop.

 

[OMTBiker]

Beautiful day today; wash, clay bar, and wax.

 

[TheWingman]

Added a couple pieces of “flair” to the tailgate and finally lopped of the aero extensions between the fender and the front bumper.

 

[JPARK60]

Just a set I ordered on amazon. Two sets. One for the sides and one for the tailgate. They just stick on top after some alcohol and careful placement. Didn’t take long at all.

How many shots of alcohol were involved, I'd think too much and placement wouldn't be optimal even with careful placement.

 

[Moab]

Just a set I ordered on amazon. Two sets. One for the sides and one for the tailgate. They just stick on top after some alcohol and careful placement. Didn’t take long at all.

Thanks and I’ll use the alcohol after I get them on. Otherwise they’ll end upside down!

 

[NC_Overland]

How many shots of alcohol were involved, I'd think too much and placement wouldn't be optimal even with careful placement.

The key is a slight beer buzz for steady hands. Too many and it’s going to go poorly.

 

[Alabama Mud Machine]

Better pics of it here at the house...

 

[TheHops]

Any tips for removing the vents from the fender? Or pretty straight forward? Hoping you can post some night time video to show them off!

It's very straightforward. They're held in place by pressure created by plastic clips. I just gently popped them out with a plastic trim tool. Just go easy on them, as I could imagine they can snap.

Truthfully, I'm not sure how to upload videos here...but this picture may prove the point. They're much brighter than the factory LED turn signals. Again, I'm very impressed...and honestly I had very low expectations.

View attachment 65727

 

[kosmos]

Installed the MPS JL Holster Molle Passenger Mount. It mounts to the passenger side of the Gladiator. Reach out to them for the "JT" laser cut VS the "JL" Great guys to deal with! JL, JLU JT Holster Panel You will need a E12 Torx bolt socket to remove the font seat bolt - I had to loosen the other side and rear as well to get the mount to slide under the seat rail - easy fast install looks great - bonus - you can still slide the seat full forward if you ever needed.



JT Holster Molle Mount



JT MPS Holster Mount

Sponsored