What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS, NO GUN TALK]

[ron168]

I also replaced the fender vents with functional turn signals. Very pleased with how they turned out! I don't have a picture of them lit up, but they're very bright. Noticeably brighter than the factory LED turn signals on the front of the fenders.

Nice additions. Curious, where did you find the turn signals? Seems like a logical place for them.

Sponsored

 

[TheHops]

Nice additions. Curious, where did you find the turn signals? Seems like a logical place for them.

Appreciate it! And, I agree. I got them from amazon myself, though I saw them on ebay too. The exact ones that I got are linked below:

https://www.amazon.com/gp/product/B082F4P3MR/ref=ppx_yo_dt_b_asin_title_o05_s01?ie=UTF8&psc=1

 

[Alabama Mud Machine]

What did I do to my Gladiator today? I bought it and drove it home.

 

[Jdyowa]

Appreciate it! And, I agree. I got them from amazon myself, though I saw them on ebay too. The exact ones that I got are linked below:

https://www.amazon.com/gp/product/B082F4P3MR/ref=ppx_yo_dt_b_asin_title_o05_s01?ie=UTF8&psc=1

I just received mine from Ebay on Friday. I haven't had a chance to install them yet. Curious, how did you wire them up? Can you tell me what lines you tapped into? It would really save me some trouble figuring it out. I've been building a room onto the house and I have been quite busy.
Thanks

 

[CMac]

New to the forum. Just picked up 2020 Gladiator and started my build immediately. Will post some pics soon.

Looks very sharp.... where'd you get the stripe/graphic set?

 

[eligius]

Added grab handles and side steps to my Rubicon.

 

[propkillr]

YOU GOT PIZZA?

 

[Jake]

Nice looking side steps! I approve.

Added grab handles and side steps to my Rubicon.

 

[JWest]

Yes there's room. See this post.

@JWest One thing I forgot to mention, the rack sits right in the middle of the back window so it does get in the way of the rear view mirror. Doesn't bother me though.

Won’t bother me either. Thx

 

[Backwoodsraider]

Added grab handles and side steps to my Rubicon.

Which steps are those?

 

[eligius]

Which steps are those?

Rampage Rock Rail Short Steps - 3 inch drop (Part # 26410034). There is more info in the "Rock Rails Thread" - link below.
https://www.jeepgladiatorforum.com/forum/threads/rock-rails-thread.16475/page-29

 

[TheHops]

I just received mine from Ebay on Friday. I haven't had a chance to install them yet. Curious, how did you wire them up? Can you tell me what lines you tapped into? It would really save me some trouble figuring it out. I've been building a room onto the house and I have been quite busy.
Thanks

Sure thing. I wired them in to the front fender turn signals. I cut 3ft length of pos/neg wire and it was the perfect length to reach the front of the fender. I used posi-taps to splice in for ease of install and to minimize damage to the harness. You could go with much shorter wires if desired, but the front of the fender provided the most room to work and would make any maintenance or troubleshooting easier down the road. The positive turn signal wire is the white and green striped one (see picture). Negative is black. Harnesses are the same for both sides. At a minimum, you'll have to remove the 3 bolts from the fender liner, and the 1 plastic rivet to get good access the harness and route the wires.

I used a wire hanger and some gorilla tape to push the wires from the vents forward through the fender. The wires ride above the fender liner through a small metal channel. Very clean install with no wires exposed.

 

[Lance126]

Finally installed lift this weekend.......
Pics, factory, factory with 37’s, 3” lift with 37’s...

 

[Gatorized]

Sure thing. I wired them in to the front fender turn signals. I cut 3ft length of pos/neg wire and it was the perfect length to reach the front of the fender. I used posi-taps to splice in for ease of install and to minimize damage to the harness. You could go with much shorter wires if desired, but the front of the fender provided the most room to work and would make any maintenance or troubleshooting easier down the road. The positive turn signal wire is the white and green striped one (see picture). Negative is black. Harnesses are the same for both sides. At a minimum, you'll have to remove the 3 bolts from the fender liner, and the 1 plastic rivet to get good access the harness and route the wires.

I used a wire hanger and some gorilla tape to push the wires from the vents forward through the fender. The wires ride above the fender liner through a small metal channel. Very clean install with no wires exposed.

Any tips for removing the vents from the fender? Or pretty straight forward? Hoping you can post some night time video to show them off!

 

[Jeeperjamie]

Did some trimming on the bumper to remove some plastic. Left the bottom plastic skid plate thing for now but trimmed up around the bumper where the fog light cover protectors are. Didn't want to completely remove them because I have read where some are having issues with their fogs starting to flicker from Mudd and trash getting in there. Here are some before and after

Sponsored